Steering Rack Side Nut Wrench for Ford USA Probe, Mazda 626 III, IV and Xedos 6 models

Mechanism for testing hps racks under load

The MS521 mechanism simulates load resistance on HPS/EPS racks, allowing precise fault detection, including leaking valves, worn seals, and cylinder wear. Works with MS502M test bench and MS561 controller.

Product code: MS521

Rear axle bushing press for Toyota Yaris, Passo, Echo

The Rear Axle Bushing Press is designed to facilitate the installation or replacement of rear axle bushings in Toyota Yaris, Passo, and Echo models. Rear axle bushing press for Toyota Yaris, Passo, Echo. Bushing

Product code: W0720

Ball joint service set

This Ball Joint Service Set is an essential toolkit for automotive professionals focusing on the removal and installation of press-fit parts. Designed for versatility and efficiency, this set is perfect for working with ball joints, universal joints, and truck brake anchor pins.

Product code: MG99028

Multi-function pneumatic hammer set, 24pcs

The 24-piece multifunction pneumatic hammer set includes an efficient air hammer with a one-button start, non-slip handle, and quick-change chisels. It's perfect for car repairs, dismantling, and more, with various accessories included.

Product code: MG99090

Front bearing hub extractor for VW Lupo, Audi A2 1.2 TDI

This Front Bearing Hub Extractor is a specialized automotive tool designed to facilitate the installation and removal of the front bearing hub on specific vehicle models, particularly the VW Lupo and Audi A2 with 1.2 TDI engines. This tool is engineered to make the process more efficient and to minimize the risk of damage to critical components such as the ABS sensor.

Product code: W0740

Press the king pins the upper and lower Jeep - Cherokee, Grand Cherokee, Wrangler

The tool is used to remove and install the kingpins in the steering knuckle assembly. Use the king pin press tool to press out the king pin from the steering knuckle. The tool will apply force to push the pin out of its housing. Once the king pin is pressed out, you can inspect it for wear or damage and replace it if necessary.

Product code: W0401

Lower kingpin puller for Jeep Cherokee, Grand Cherokee, Wrangler

This lower kingpin puller is designed for the knuckle pin assembly and disassembly, specifically for use on the car's bottom. It ensures efficient and safe operations for Jeep models.

Product code: W0399

Adapters to bolts down Jeep - Cherokee, Grand Cherokee, Wrangler

Product code: W0398

Crankshaft Pulley/Damper Removal Tool Jaguar, Land Rover

A set of tools for the removal of the front crankshaft pulley (crankshaft vibration damper) fitted to the Jaguar, Land Rover 3.0L V6 and 5.0L V8 petrol engines.

Product code: CKB10435

Rear bearing hub puller, Citroen; Peugeot ; Toyota ; Opel after 2016

This tool is designed for the removal and installation of wheel bearings, especially on specific vehicles models after 2016. The design eliminates the need to remove the steering knuckle and ABS sensor and simplifies the repair process.

Product code: W0736

Front sled bushing puller Renault Laguna II, Trafic II

This is a tool used to remove the bushings in the front suspension of Renault Laguna II and Renault Trafic II cars.

Product code: W0368

Inner tie rod master tool kit with 12 adaptors

Inner tie rod master tool kit with 12 adaptors. Long socket and crowfoot design for easy removal and installation without removing the rack. Includes crowsfeet sizes from 29mm to 42mm and 1-3/16" to 1-1/2".

Product code: MG91049

Tool for hub removal (set of 15 screws)

Tool for hub removal – cars of A, B, C class and others. Set of 15 screws.

Product code: W0072

Sleeve puller, rear beams, Fiat Punto

Sleeve puller for rear beams on Fiat Punto, designed to replace bushings. Can be used universally on a car or with a hydraulic press.

Product code: W0058

Adapters for suspension arm sleeves, front, Mercedes C-class, 2001-07

Adapters for suspension arm sleeves, front, MERCEDES C-class, 2001-07. It serve for sleeves pulling and pushing with using of hydraulic press.

Product code: W0050

Universal sliding hammer hub puller, with 15 screws

Universal sliding hammer hub puller with 15 screws, ideal for removing seized hubs. The tool weighs 13kg and comes with three types of 5 screws for various applications. Size range: 90mm-155mm (±5mm), with an external flange dimension of 185mm.

Product code: W0002

Puller arm forward bushing Renault Laguna I (under a hydraulic press)

Puller arm forward bushing Renault Laguna I (under a hydraulic press) (nr. oe 77 00 822 503)

Product code: W0170

Double-row bearing puller and wheel hubs II version (BMW, Mercedes etc.)

Double-row bearing puller and wheel hubs II version (BMW, Mercedes etc.)

Product code: W0205

Rear beam bushing puller for BMW X5 E53

Rear beam bushing puller (No. oe 33 17 6 770 456) for BMW X5 E53

Product code: W0246

Rear axle bush puller for Volkswagen / Audi / Seat after 2004

Rear axle bush puller for Volkswagen, Audi, and Seat models post-2004. Ideal for precise and efficient removal of rear axle bushes.

Product code: W0311

Upper knuckle pin press for Cherokee, Grand Cherokee, Wrangler

Upper knuckle pin press for Cherokee, Grand Cherokee, and Wrangler models. Designed for precise removal and installation of top pins.

Product code: W0313

Rear beam bushing puller Renault Laguna II set (5 adapters)

Rear beam bushing puller set for Renault Laguna II, includes 5 adapters for both original and non-original bushings. Suitable for modified and unmodified bushings.

Product code: W0330

Front control arm bushing puller Renault Clio II; Renault kangoo I; Thalia I (7700424399 )

Front control arm bushing puller for Renault Clio II, Kangoo I, and Thalia I. Suitable for mounting and dismounting both bushings in the swingarm.

Product code: W0337

Puller sleeves for the left front beam Ford Focus II; III; C-Max; Volvo

Puller sleeves for the left front beam in Ford Focus II, III, C-Max, and Volvo S40 II, V50. For mounting and removing bushings directly on the car. Compatible with OE bushings: FM-FOC4, 1695011, 1355621, 23032, 30666042.

Product code: W0369

Puller sleeves for the right front beam Ford Focus II; III; C-Max; Volvo S40II, V50

Puller Sleeves for Right Front Beam – Ford Focus, C-Max, and Volvo. These puller sleeves are designed for mounting and dismounting bushings on various models of Ford and Volvo vehicles, ensuring precise and efficient maintenance. Compatible with several Ford Focus and Volvo models from 2003 onwards.

Product code: W0370

Bearing Hub Puller Renault Trafic , Opel Vivaro 2.0 DCI

Bearing Hub Puller for Renault Trafic and Opel Vivaro 2.0 DCI models. Designed for efficient removal of wheel hubs during maintenance.

Product code: W0487

Rear axle nuts wrench for Mercedes Sprinter W901 and W905

Key for unscrewing rear axle nuts on Mercedes Sprinter W901 and W905 models. Compatible with nut 902 357 01 26.

Product code: W0598

Steering readout scale, 270-350mm

This Steering wheel level is a specialized tool designed to assist in the accurate leveling of a vehicle's steering wheel before it is locked into position. This step is crucial prior to checking or adjusting the front wheel alignment.

Product code: MG99230

Axial joint tool, 27-42mm

Axial joint tool, 27-42mm can be used to remove and attach the axial joints.

Product code: MG50444

Axial joint tool, 33-42mm

High-quality axle joint installation tool, specially designed for quick and efficient removal and installation of vehicle axle joints. Thanks to its 1/2" drive, the tool is easy to use with many manual and pneumatic wrench systems.

Product code: MG50443

Wheel Bearing tool VW

Bearing installation and removal tool for 85mm bearings. Application Volkswagen Touareg, Transporter, Multivan & T5

Product code: MG50432A

Steering rack knuckle tool set, 30-45mm

This steering rack knuckle tool set makes removing and installing steering knuckles fast and easy. With interchangeable heads to fit racks with hex drive, two flats, and round ends from 30-45mm, it's versatile and effective. Drive: 32mm Hex, 1/2" square.

Product code: MG50423

CV boot band pliers

For stainless steel CV boot bands. Also for bands, where special torque has to be used, Volkswagen, Audi, Opel, Ford

Product code: MG50111

CV Boot Clamp Pliers, 184mm

CV Boot Clamp Pliers, 184mm 1/2" holes on the handles can be used as keys.

Product code: MG50110

Universal silent block removing and installing kit, 34-84mm

Spindle: M10xP1.5, M12xP1.75, M14xP2.0, M16xP2.0, length/Ø A 44/34, 46/36, 54/44, 56/46, 58/48, 66/56, 68/58, 70/60, 78/68, 80/70, 84/72, B 48/38, 50/40, 52/42, 60/50, 62/52, 64/54, 72/62, 74/64, 76/66mm

Product code: MG50093

Wheel bearing removal/installation tool set 50-88mm

Diminishes the possibility of wheel bearing damage during removal and installation. Sizes (d) 50, 55, 60, 64, 67, 70, 72, 74, 75, 78, 82, 84, 88mm.

Product code: MG50075

7pcs Drive Shaft Puller / Extractor Set

The 7pcs Drive Shaft Puller / Extractor Set is suitable for pulling the half-axle into the wheel hub. In order to be able to carefully and evenly insert the half-axle into the wheel hub, it is necessary to use the appropriate adapters and accessories from the drive-in tool, so that the half-axle goes in securely and straight.

Product code: MG50046

Ball joint separator set, 5pcs

Ball joint separator set, 5pcs ideal for assembling and disassembling wishbones,, ball joints, socket joints, tir rods and individual gimbal joints.

Product code: MG04B3051

Adjustable Steering Rod Wrench, 1/2", 25-55mm

The 1/2" Drive Steering Rack Wrench is used to loosen or tighten the bolts and nuts that secure the steering rack to the vehicle's chassis. The tool is designed with a 1/2" drive socket that allows it to fit over the nuts and bolts with ease. The wrench is typically adjustable, allowing it to fit various sizes of nuts and bolts.

Product code: MG04B3042

Ball joint separator 39mm

Steering rods, stabilizers, etc. designed to remove ball-jointed rotating parts.

Product code: MG04B3022D

Ball joint separator 18mm

Steering rods, stabilizers, etc. designed to remove ball-jointed rotating parts.

Product code: MG04B3022A

Ball joint separator 19-22mm

Steering rods, stabilizers, etc. designed to remove ball-jointed rotating parts.

Product code: MG04B3022

CV Boot Tool

CV Boot Tool is allows the convenient and efficient installation of rubber bells on the half-axle of the vehicle.

Product code: MG04B1099

Pneumatic CV joint boot install tool

This pneumatic CV joint boot install tool makes installation fast and easy. It prevents boot damage and ensures a tight fit. Simply adjust the air control switch and place over the CV joint. Lubricate before use. Working pressure: 5-9bar. Perfect for auto mechanics!

Product code: MG04B1085

CV joint assembly removal tool

Can be used in almost all vehicles. It is suitable for replacing damaged, worn out axle hinges quickly and without any problems.

Product code: MG04B1012

Cv boot clamp tool with cutter

Cv boot clamp tool with cutter is suitable for installing and tightening tape-type clamps. It has a built-in cutter for cutting tape. With the built-in cutting and winding mechanism, the tape can be pulled and cut quickly and efficiently.

Product code: MG04B1008

CV Clamp Tool and CV Joint Boot Clamp Pliers Set

The 2-piece pliers set for quick and easy tightening and fastening of rubber bell clamps. Ideal for installing half-shaft rubber bells.

Product code: MG04B1007

Wheel hub socket wrench set, 8 pcs

This set is specially designed for loosening and tightening nuts drilled into the upper part.

Product code: MG04A2268D

Sleeve, bearing and silent press kit, 27pcs

Inside diameters from 34-80mm in 2mm steps, outside diameters from 44-80mm in 2mm steps, pulling spindles with nuts.

Product code: DK-230581A

Front control arm bush puller Renault Laguna, Espace, Trafic, Opel Vivaro

Front control arm bush puller for Renault Laguna, Espace, Trafic, and Opel Vivaro. Compatible with OE bushings No. 82 00 002 869. Ideal for bushing removal and installation.

Product code: W0326

Puller for wheel hub / bearing Ford Focus II, C-Max, Volvo, Mazda 3,-puller with ABS and without ABS

This tool is designed for the assembly and disassembly of wheel hubs and bearings on the car, compatible with both ABS and non-ABS systems.

Product code: W0305

Rear beam bushing puller for Renault Laguna II (for non-factory bushings with flat back)

This rear beam bushing puller is designed specifically for Renault Laguna II, making the removal of non-factory bushings with a flat back efficient and safe.

Product code: W0329

Front control arm bush puller Renault Laguna II; Espace IV ( nr oe 8200002868; FE22821 )

This tool is used for mounting and dismounting the bushing.

Product code: W0334

Adapters for removing and installing the rocker pin Mercedes W124

These adapters are essential tools for the disassembly and assembly of the control arm pin, ensuring efficient and precise work when paired with the Press W0099.

Product code: W0349

Puller for wheel hub / bearing with and without Abs - Ford Mondeo, Focus, C-Max, Mazda 3, Volvo C30 C70 S40 V50

The wheel hub/bearing puller allows you to install and remove the hub/bearing on the car without removing the ABS sensor.

Product code: W0359

Front Sledge Bush Puller for MERCEDES ML W163

The front sledge bush puller is specifically designed for Mercedes ML W163 models, suitable for the removal and installation of front suspension bushings. This tool allows for efficient work directly on the vehicle, simplifying and speeding up the maintenance process.

Product code: W0428

Rear axle silent puller

The rear axle silent puller is a special tool used to remove and install the metal-rubber bushings in the rear suspension of vehicles on various Honda and Rover models (Honda Civic, CR-V, Concerto, CRX, Rover 200).

Product code: W0485

Hub and Bearing Puller for Fiat Ducato and Citroen Jumper

This hub and bearing puller is specifically designed for Fiat Ducato and Citroen Jumper vehicles, allowing for the quick and efficient mounting and dismounting of hubs and bearings on the vehicle without the need to disassemble the suspension.

Product code: W0499

Mercedes Smart Hub Pressing Adapter Set

Hub pressing adapter set for Mercedes Smart vehicles, designed for precise and efficient hub installation and removal.

Product code: W0575

Wheel hub nut wrench rear Toyota Land Cruiser ( 09509-25011 )

Rear wheel hub nut wrench for Toyota Land Cruiser, designed for secure and precise removal and installation. Compatible with OE Tools 09509-25011 and OE Nuts 42427-60021.

Product code: W0612

Wrench / Cap for loosening the wheel hub nut IVECO DAILY 55s17 4x4 REAR (oe nuts 42558514)

Wrench/Cap for loosening the rear wheel hub nut on IVECO Daily 55s17 4x4, compatible with OE nut 42558514.

Product code: W0622

Rear upper control arm bush puller for Toyota Avensis II, Celica, Auris, and Lexus CT

Rear upper control arm bush puller for Toyota Avensis II, Celica, Auris, and Lexus CT. Compatible with OE bushings 48770-05010 and 48770-21011.

Product code: W0628

Power steering pump pulley service kit, 7pcs

7-piece power steering pump pulley service kit for removing and installing pulleys with 1-1/8", 1-1/4", 1-5/16", and 1-3/8" hubs. Compatible with Saginaw, Thompson, and Ford C111 C2 power steering pumps in most Ford, GM, and Chrysler vehicles.

Product code: MG94042

Ball joint extractor set, 24/27/32/36mm

Ball joint extractor set with sizes 24mm, 27mm, 32mm, and 36mm. Ideal for removing ball joints from various vehicles efficiently.

Product code: MG99075

Ball joint extractor set, 22/24/27/32/36mm

Ball joint extractor set with sizes 22mm, 24mm, 27mm, 32mm, and 36mm. Ideal for removing ball joints from various vehicles efficiently.

Product code: MG99075A

Ball joint seperator for pin diameters up to 19mm

Professional ball joint pin puller. It is made of durable, high-quality tool steel. It is adapted to work with pins with a diameter of not more than 19mm.

Product code: G02587

5pcs strut nut tool set for Audi, VW and Mercedes

A set of nut tools for tightening and loosening shock absorber mounts.

Product code: G02785

Steering rack bushing tool for Ford models

The Specialized Nut Socket by MSG Equipment is a high-quality tool designed for the installation and removal of the bearing bushing in the steering rack.

Product code: MS00012

Steering rack bushing tool for Mazda 6 models

Specialized tool for mounting and dismounting the bearing bushing of the steering rack. Designed for Mazda 6 models, ensuring easy and damage-free maintenance.

Product code: MS00038

Steering rack bushing tool for Nissan, Opel, Renault models

A specialized nut socket for safe installation and removal of steering rack bearing bushings for Nissan, Opel, and Renault models.

Product code: MS00064

Steering rack bushing tool for Lexus and Toyota models

Efficient tool for mounting and dismounting steering rack bushings without deformation. Suitable for Lexus LX, Toyota Land Cruiser Amazon, and Prado models.

Product code: MS00021

Steering rack bushing tool for Honda models

Specialized tool for safely mounting and dismounting steering rack bushings, preserving aluminum alloy nuts. Compatible with Honda Accord VIII sedans and wagons. Work with this device is carried out with a wrench.

Product code: MS00023

Steering gear lock nut removal tool for Hyundai, Mitsubishi and Nissan models

A specialized tool designed to safely remove the steering gear lock nut in select Hyundai, Mitsubishi, and Nissan models, preventing damage during disassembly.

Product code: MS00047

Fitting for testing power steering pump on a test bench for Audi, BMW, Mercedes, Opel and VW models

A fitting for connecting power steering pumps to a test bench for diagnostics, compatible with a wide range of Audi, BMW, Mercedes-Benz, Opel, and VW models.

Product code: MS00063

Shock absorber spring compressor, heavy duty, 2.3t

Macpherson spring compression tool. Adjustable 100-265mm. Fits most car models. Drive: 24mm allen.

Product code: MG94227

Universal suspension strut holder for transmission jacks

This tool is securely holds suspension struts during repairs and maintenance.

Product code: MG99600

Universal silent block hydraulic extractor and installer set

Comprehensive silent block extractor and installer set with hydraulic capability, 44 mandrels (short and deep), power screws, and a hydraulic cylinder for universal automotive applications.

Product code: MG92611A

Drive shaft impact socket set, 12pt 30-36mm, hex 14-19mm, 8pcs

A professional-grade drive shaft impact socket set, including 12-point sockets (30–36mm) and hex sockets (14–19mm), designed for heavy-duty applications.

Product code: MG93301

Hydraulic wheel hub puller 10T

Powerful hydraulic wheel hub puller for 4- or 5-bolt hubs. Compatible with various car brands, handles 10T hydraulic force, and fits bolt patterns within 11mm-148mm diameter.

Product code: MG04B1044B

Tester for diagnostics of electric power steering units

The MS561 PRO is a professional diagnostic tester for standalone Electric Power Steering (EPS) units, supporting CAN, CAN-FD, and FlexRay protocols. It enables in-depth diagnostics, VIN programming, and error clearing for nearly 4000 car models.

Product code: MS561 PRO

Special wrench for disassembling of power steering pump

Special wrench for safe disassembly of power steering pump covers with complex shapes. Prevents damage, works with 22 mm wrenches, compatible with Nissan and Renault models.

Product code: MS00041

Tester for diagnostics of power steering system

The MS511 tester is designed for diagnosing power steering system components such as steering racks and pumps without removal from the vehicle. It evaluates fluid pressure and flow rate, helping determine if repairs are needed.

Product code: MS511

Tester for diagnostics of power steering system

The MS510 tester is used for diagnosing the hydraulic power steering system by determining the pressure generated by the vehicle's power steering pump in different operating modes (with load and without).

Product code: MS510

Test bench for diagnostics of power steering pumps

Test Bench MS504 is used for evaluation of the technical condition and output characteristics of mechanically driven single- and double-circuit pumps. The bench simulates operation of the tested unit in a car.

Product code: MS504

Test bench for diagnostics and flushing of power steering system

MS503N is a universal test bench for power steering systems operated from 230V mains. The test bench for system flushing and evaluation of the technical condition of a power steering rack or pump.

Product code: MS503N

Test bench for diagnostics of power steering racks

The MS502M test bench is designed for hydraulic power steering (HPS) rack diagnostics, allowing real-time performance simulation and detection of faults like leaks, packing seal wear, unit body damage, and Teflon ring deterioration.

Product code: MS502M

Steering rack shaft polishing machine

The MS402 polishing machine is designed for grinding and polishing steering rack shafts and other cylindrical components. It removes corrosion and ensures precise surface roughness. Works with 900mm max shaft length and operates at 1500 RPM.

Product code: MS402

Devices for refueling shock absorbers

A specialized system for refilling mono-tube and twin-tube shock absorbers with gas after repair, with pressure adjustment up to 120 bar.

Product code: MS200

Test Bench for shock absorbers

A professional test bench for evaluating the performance of all types of passenger car shock absorbers, supporting diagnostics, post-maintenance checks, and research applications.

Product code: MS201

Puller for the power steering pump pulley hub

Specialized tool for dismounting power steering pump pulley hubs during hydraulic system repairs. Minimum risk to damage the pump itself in repair.

Product code: MS00004

Steering Rack Side Nut Wrench for Opel models

This specialized wrench is designed for quick and efficient installation or removal of steering rack side tightening locknuts. It ensures safe operation by eliminating the risk of damaging the locknut during use. Manufactured by MSG Equipment, the tool is compatible with various Opel models.

Product code: MS00006

Steering Rack Side Nut Wrench for Lexus and Toyota models

Specialized nut socket for easy installation, removal, and adjustment of steering rack side tightening nuts, ensuring damage-free and precise repairs. Compatible with select Toyota models. Manufactured by MSG Equipment.

Product code: MS00007

Steering Rack Side Nut Wrench for Citroen and Peugeot models

Specialized nut socket for easy installation, removal, and adjustment of steering rack side tightening nuts, ensuring damage-free and precise repairs. Compatible with select Citroen and Peugeot models. Manufactured by MSG Equipment.

Product code: MS00008

Wrench for bottom nut of worm gear steering rack for numerous models

This specialized nut socket is designed for the precise installation and removal of the bottom nut of the steering rack worm gear. It ensures safe, damage-free handling and high-quality repairs for steering rack pinions. It is suitable for the following models: Chrysler, Citroën, Ford, Hyundai, Kia, Mazda, Mitsubishi, Peugeot, Seat, Volkswagen (VW).

Product code: MS00009

Steering Rack Side Nut Wrench for Dodge, Mercedes-Benz, VW

This specialized nut socket is designed for efficient mounting, dismounting, and adjustment of steering rack side tightening nuts. Manufactured by MSG Equipment, it ensures safe and damage-free handling during steering system maintenance and repair.

Product code: MS00010

Steering Rack Side Nut Wrench for Ford, Nissan, Renault, Volvo, Lincoln models

Special tool for safe mounting, dismounting, and adjusting aluminum alloy steering rack nuts, preventing damage. Works with a wrench for precise handling.

Product code: MS00011

Wrench for upper nut of worm gear steering rack for Nissan models

Specialized nut socket for efficient and safe installation/removal of the upper nut of the worm gear in steering racks, compatible with select Nissan models (Murano Z50, Teana J31, 2003-2008).

Product code: MS00018

Wrench for upper nut of worm gear steering rack for Infiniti and Nissan models

Specialized nut socket for efficient and safe installation/removal of the upper nut of the worm gear in steering racks, compatible with select Infiniti and Nissan models.

Product code: MS00019

Wrench for upper nut of worm gear steering rack for Lexus, Toyota and VW models

Specialized nut socket for efficient and safe installation/removal of the upper nut of the worm gear in steering racks, compatible with select Lexus, Toyota and VW models.

Product code: MS00020

Steering rack bushing tool for Ford and Mazda models

Specialized tool for safely mounting and dismounting steering rack bushings, preserving aluminum alloy nuts. Compatible with Ford Fiesta V, Ford Fiesta Van, Ford Fusion and Mazda 2.

Product code: MS00024

Wrench for upper nut of worm gear steering rack for Subaru models

Specialized nut socket for efficient and safe installation/removal of the upper nut of the worm gear in steering racks.

Product code: MS00025

Steering rack bushing tool for Mazda 323 models

Specialized tool for safely mounting and dismounting steering rack bushings. This tool prevents bushing from deformation. Compatible with Mazda 323 C, F, S IV models.

Product code: MS00027

Steering rack bushing tool for Lexus GX and Toyota models

Specialized tool for safely mounting and dismounting steering rack bushings. This tool eliminates the risk to damage bushing in the process of its assembling and disassembing. Compatible with Lexus GX (2001-2009) and Toyota models.

Product code: MS00028

Steering rack adjusting tool for side nuts for Lexus, Mazda and Toyota models

Effortlessly mount, dismount, and adjust side tightening nuts of steering racks without deformation. Compatible with various Lexus, Mazda, and Toyota models.

Product code: MS00029

Wrench for upper nut of worm gear steering rack for Nissan Navara, Pathfinder models

Specialized tool for quick and safe installation/removal of the upper nut of the worm gear in steering racks. Designed for Nissan Navara (D40) and Pathfinder (R51), ensuring quality repair.

Product code: MS00033

Steering Rack Side Nut Wrench for MITSUBISHI LANCER IX

Specialized tool for easy installation, removal, and adjustment of the steering rack side tightening nut. Designed for Mitsubishi Lancer IX models, ensuring damage-free maintenance.

Product code: MS00035

Steering rack bushing tool for Ford and Nissan models

Specialized tool for quick installation and removal of steering rack bearing bushings. Manufactured by MSG Equipment, designed for Ford and Nissan models, ensuring efficient and deformation-free maintenance.

Product code: MS00039

Power steering pump hub puller

A universal power steering pump hub puller for quick and safe removal of pulley hubs without deformation. Compatible with all car models.

Product code: MS00042

Steering rack bushing tool for Ford Focus, Tourneo and Transit models

Specialized steering rack bushing tool for Ford Focus, Tourneo and Transit models, ensuring quick and damage-free installation or removal of bearing bushings.

Product code: MS00044

Pressing screw for hub and pulley of power steering pump (M12/1,5) for MS00126 tool

Universal pressing screw (M12/1.5) for press-fitting hubs and pulleys on power steering pump shafts. Compatible with all vehicle makes and models.

Product code: MS00046

Pressing screw for hub and pulley of power steering pump (BSW 3/8") for MS00125 tool

A special tool for press-fitting a hub or a pulley on the power steering pump shaft. The tool is universal and applicable to all vehicle makes and models. The purpose of the tool is to assist in the pump assembly after its repair.

Product code: MS00055

Pressing screw for hub and pulley of power steering pump (М8×1,25) for MS00125 tool

A special tool for press-fitting a hub or a pulley on the power steering pump shaft. The tool is universal and applicable to all vehicle makes and models. The purpose of the tool is to assist in the pump assembly after its repair.

Product code: MS00056

Pressing screw for hub and pulley of power steering pump (BSW 3/8") for MS00126 tool

A special tool for press-fitting a hub or a pulley on the power steering pump shaft. The tool is universal and applicable to all vehicle makes and models. The purpose of the tool is to assist in the pump assembly after its repair.

Product code: MS00057

Oil seals extractor from hydraulic cylinder of steering rack

Oil seal extractor for hydraulic cylinders of steering racks, suitable for seals with an inner diameter of 20–30 mm and depths up to 400 mm.

Product code: MS00058

Oil seals extractor head (20/30 mm)

Extractor head for quick removal of oil seals (20–30 mm) from hydraulic cylinders, designed to prevent deformation and damage. Compatible with MS00005 and MS00058 oil seals extractor tools.

Product code: MS00059

Set of fittings for connection of steering rack to a test bench for BMW 7, BMW X3 models

A set of fittings for securely connecting steering racks to a test bench, compatible with BMW 7 (E65, E66) 2005–2008 and BMW X3 (E83) 2008–2011.

Product code: MS00060

Set of fittings for connection of steering rack to a test bench for Audi A4, A5, A8, Q5 models

A set of fittings for securely connecting steering racks to a test bench, designed for diagnostics of steering rack technical conditions, compatible with specified Audi models.

Product code: MS00061

Steering rack bushing tool for Nissan Navara and Pathfinder models

Specialized nut socket for safe installation and removal of steering rack bearing bushings, designed for Nissan Navara and Pathfinder models.

Product code: MS00066

CV boot clamp pliers (ear type)

CV boot clamp pliers suitable for Oetiker CV drive shaft boot securing clips. Plier's plate presses a flat on the top of the clip so that it forms the spring loop correctly.

Product code: G01656

CV joint clamp banding tool

CV joint clamp banding tool is suitable for installation and tightening of band-style clamps on CV joint boots, power steering rack and pinion steering gear boots.

Product code: G01653

Ball joint removal tool set

Designed for easy removal of most popular types of pitman arms, tie rods and ball joints. Operation range: 17, 19, 21, 23, 27mm

Product code: CKB04340

Bushing and silent press for Mercedes, VW, Renault, Opel, Nissan

The tool is used for pressing in and out the pins and silents without the disassembly of the control arm, thus saving you time and energy.

Product code: C02/0140

Renault and Peugeot rear axle bush remover and installer

Designed for the removal, installation and alignment of rear axle bushes on Renault Laguna II and Peugeot 207.

Product code: C02/0094

Puller for wheel hub / bearing VW Polo, Seat, Skoda, Audi A2-puller with ABS and without ABS

This puller is specifically designed to handle wheel hubs and bearings on VW Polo, Seat, Skoda, and Audi A2 vehicles. Whether your vehicle is equipped with ABS or without ABS, this versatile tool ensures a secure grip and effortless removal.

Product code: W0306

Wheel hub nut socket wrench for Renault

Wheel hub nut socket wrench for Renault Mascott, Midlum, Premium (nut OEM 5010372353).

Product code: W0309

Sleeve puller for Opel rear beams

Rear bushing puller for Zafira B, Astra H, Meriva. For the assembly and disassembly of sleeves in cars.

Product code: W0372

Key to loosening the rear hub nuts M55X1,5 Mercedes Sprinter, VW Crafter after 2006 (hardened)

Key to loosening the rear hub nuts is designed to fit the specific dimensions of the hub nut and provide the necessary grip and torque for loosening it.

Product code: W0403

Rear beam silent puller for Renault Laguna III and Laguna Coupe

Rear beam bushing puller for Renault Laguna III and Laguna Coupe. OEM: 55 04 400 01R, 55 04 466 24R, 55 04 500 01R.

Product code: W0503

Ball joint removal set, 5pcs

Designed for easy removal of most popular types of pitman arms, tie rods and ball joints. Operation range: 17, 19, 21, 23, 27mm

Product code: DK-230506

Universal silent and bearing puller kit, 24pcs

This professional tool set is designed for the removal and installation of bushings, silent bearings, hydraulic bearings and seals, etc.

Product code: DK-230581

Heavy-duty spring compressor 2.3t

Macpherson spring compression tool. Adjustable 100-265mm. Fits most car models. Drive: 24mm hex.

Product code: MG04B2116

Rear trailing arm bushing removal tool for Ford and Volvo

Remove and install rear trailing arm bushings on Ford and Volvo vehicles without disconnecting brake lines or removing bolts. Fits multiple models. OEM code 205-1017.

Product code: MG04B2126

Axle nut socket set, 9pcs

Axle nut socket set, 9pcs is a special set of tools required for tightening and loosening vehicle axle nuts. These types of nuts are usually large and overtightened and require special wrenches to fit their size and shape.

Product code: MG04B1015

Ball joint separator, scissor type

Ball joint separator, scissor type has a heat-treated and drop-forged steel body and screw, making it a very durable and long-lasting tool.

Product code: MG04B3016

CV boot clamp pliers

The Half Shaft Joint Clamp Pliers is a special tool that can be used for crimping stainless steel strips. The tool comes with an adapter that is 3/8" in size, making it compatible for use with a torque wrench. For smooth operation of the tool, it is recommended to grease the lead screw thread. This will help reduce friction and result in smoother operation.

Product code: CKBA1093

KM10 socket wrench for unscrewing the wheel hub nut of the Mercedes G class

The socket wrench is specifically designed for the precise and safe removal and installation of the wheel hub nuts of Mercedes G class cars. With its dimensions and design, the socket wrench ensures an optimal fit with the wheel hub nuts, allowing them to be handled quickly, easily and without damage.

Product code: W0504

Rear Suspension Bush Puller Ford Mondeo

Rear beam bushing puller for Ford Mondeo, designed to press in and remove bushings without disassembling the swingarm.

Product code: W0020

Universal silent block remover/installer set, 34-72mm, 44-82mm

Our universal silent block remover/installer set makes extracting and installing silent blocks, hydraulic bearings, and more a breeze! With spindles and press adapters in various sizes, this set is perfect for any job.

Product code: MG50605

Wheel hub puller set, M12 X 1.5, M14 X 1.5

Wheel hub puller set, suitable for VW, Audi, Alfa Romeo, Ford, Citroen, BMW, Mazda, Fiat, Mercedes-Benz, Seat, Opel, Peugeot, Renault, Skoda, Porsche

Product code: MG50438

Ball joint separator tool set, replaceable heads, 20, 22, 24, 27, 30mm

The Ball Joint Separator Tool Set designed to facilitate the easy and safe removal of ball joints from vehicles. This set is particularly valuable due to its versatility and efficiency in handling different sizes of ball joints, which is achieved through its set of replaceable heads and adjustable features.

Product code: MG50436

Wheel bearing removal/installing tool set

For the VAG group, wheel hub size 72mm, Audi A2, Skoda Fabia after 2000, VW Polo, Fox after 2005, Seat Ibiza after 2002.

Product code: MG50432

3pcs Ball joint remover set. Diameters: 23, 28, 34mm

Pullers for ball joints on stabilizers and torsion bars. Suitable for cars and vans.

Product code: G02585

Ball joint separator and installer tool set

This ball joint tool kit is suitable for removing and fitting press-fit type ball joints without removing the vehicle's control arm. The pressing device's gap size is 152mm.

Product code: CKB04011

Press for silents and bushings for VW T4, LT, Crafter and Mercedes Sprinter

The tool is used for pressing in and out the pins and silents without the disassembly of the control arm, thus saving you time and energy.

Product code: C02/0144

Universal press for extracting and pressing pins and silents

Its main purpose is the disassembly and assembly of silents in the suspension. Adapters not included.

Product code: C02/0135

Universal ball joint puller for pins up to 20mm in diameter.

Universal ball joint puller with lever. Made of forged steel. Its compact size allows you to work in hard to reach areas.

Product code: G02583

Bushing puller for the rear control arm of Renault suspensions

Sleeve puller for rear control arm of Renault Clio II, Thalia, Twingo II, III.

Product code: W0079

Wrench for damper pin locking/unscrewing, Ducato, Jumper, Boxer

This specialized wrench is exclusively designed for the precise task of locking and unscrewing damper pins on vehicles like the Ducato, Jumper, and Boxer.

Product code: W0090

Rear beam sleeve puller, FIAT Punto II

The puller is specifically designed to fit the rear beam bushing sleeves of FIAT Punto II, ensuring a precise and secure grip during the extraction process.

Product code: W0106

Puller sleeve (only for pressing) of the rear beam Citroen, Peugeot

Puller sleeve (only for pressing) of the rear beam Citroen C4, Peugeot 307.

Product code: W0186

Ball joint wrench for Kia, Hyundai front arm pins, hexagonal extension

Ball joint wrench for Kia Creed, Hyundai i30 front arm pins, hexagonal extension. OE: J4860323, KI-BJ-13409, V53-0107.

Product code: W0474

Puller for rear steering knuckle bushing for KIA and Hyundai

Rear steering knuckle silent puller for KIA, Hyundai.

Product code: W0667

Press for disassembly and assembly, bolts Ford Transit VI MK6

This press tool is a special tool used to disassemble and reassemble the kingpin of a Ford Transit VI (MK6) type vehicle.

Product code: W0681

Front wheel drive kit, 55.5-91mm, axle 380mm

Front wheel drive kit with a range of 55.5-91mm and 380mm axle. Includes universal front hub and bearing installer/puller with M12x1.5mm and M14x1.5mm adapters.

Product code: MG50405

Axial joint puller 35-45mm

Suitable for quick and easy removal/installation of the steering knuckle. Clamping size 35-45mm, length 400mm, hexagon end 27mm (1/2"DR)

Product code: MG50045

Ball joint and silent block remover/installer set

Suitable for any passenger car, utility trucks and SUV vehicles, in which the ball joints have an interference fit. The tools allow for easy removal and installing without large-scale demounting.

Product code: MG50042

Ball joint separator, 18mm, two-staged, max. size 50mm

A ball joint, ball head and rod end extractor is a special tool that helps to easily remove these parts from vehicles such as suspension or steering.

Product code: MG50032

Pneumatic CV boot installation tool (8bar)

The CV boot installation tool is to be used solely for the stretching of flexible CV boots onto drive-shaft assemblies of automotive vehicles.

Product code: JBM52994

Boot clamp set 2pcs

After removing a broken CV boot use these clamps to fasten the new CV boot to the vehicle's axle-shaft. Covers sizes from 15 to 125mm (15 to 45mm and 50 - 125mm).

Product code: JBM52633

CV joint boot clamp pliers

CV joint boot clamp pliers. Holes of 1/2" on the handles to use as keys. Opening: 0-20mm.

Product code: JBM52619

Wheel bearing removal/installation tool set 55.7-88.4mm

Diminishes the possibility of wheel bearing damage during removal and installation. Sizes (d) 55.7, 63.3, 67.8, 70.7, 71.9, 71.7, 72.8, 73.4, 74.7, 77.4, 81.4, 83.3, 88.4mm.

Product code: JBM52551

Universal press and pull sleeve kit, 34-82mm

Spindle: M10, M12, M14, M16, M18, Adapters (Outer/inner diameter): 74/54mm, 76/56mm, 78/58mm, 72/52mm, 70/50mm, 68/48mm, 80/60mm, 82/62mm, 66/46mm, 64/44mm

Product code: JBM52494

Clamp 15-45mm

This tool is designed to hold, clamp or encircle one or more objects, e.g., cables or pipes.

Product code: JBM11891

Clamp 50-125mm

This tool is designed to hold, clamp or encircle one or more objects, e.g., cables or pipes.

Product code: JBM11890

Universal FlexRay Cable

The MS39000 Universal FlexRay Cable enables diagnostics of FlexRay-controlled EPS units removed from a vehicle. It works with the MS561 PRO tester, providing error reading, real-time data viewing, and control unit analysis with a single cable.

Product code: MS39000

Inner tie rod remover and installer tool. For rod diameters: 35-41mm

Inner tie rod remover and installer tool. For rod diameters: 35-41mm. Length: 400mm.

Product code: G02548

Inner tie rod remover and installer tool. For rod diameters: 28-35mm

Inner tie rod remover and installer tool. For rod diameters: 28-35mm. Length: 400mm.

Product code: G02547

CV Joint boot clamp pliers set, 2pcs

The 2pcs CV joint boot clamps pliers set is a banding tool for fast and simple tensioning and securing of CV boot banding straps. Ideal for installing bellows.

Product code: CKB04121-D

Ball joint, tie rod, and pitman arm separator set (5pcs)

Ball joint, tie rod, and pitman arm separator for cars and light trucks. 5pcs set. Forks are designed to interchange with either of the handles.

Product code: CKB04028

Ball joint press set

For the removal of ball joints, U-joints, brake anchor pins, and more on most 2 wheel drive (2WD) and 4 wheel drive (4WD) vehicles without removing the control arm from the vehicle.

Product code: CKB04009

Hollow hydraulic cylinder 20t

Hydraulic cylinder with through and threaded hole. It can be used with various types of mechanical presses that are designed for the extraction of metal and rubber silents, pins, joints, etc.

Product code: C07/0112

Hollow hydraulic cylinder 12t

Hydraulic cylinder with through and threaded hole. It can be used with various types of mechanical presses that are designed for the extraction of metal and rubber silents, pins, joints, etc.

Product code: C07/0098

Bushing extractor and installer for Ford and Volvo

The tool is used to install and extract bushings and silents without disassembling the control arm. Enables the replacement of bushings in 4-wheel drive (4x4) cars.

Product code: C04/0211

Adapter set for link pivot pin bushings and silents in Renault, Opel and Nissan cars

Adapter set for silents of upper link pivot pins in Opel Movano, Renault Master, Nissan Interstar.

Product code: C02/0147

Adapter set for bushings of swingarm pins for VW T4, LT, Crafter, Mercedes Sprinter

Adapter set for bushings of swingarm pins for VW T4, LT, Crafter, Mercedes Sprinter

Product code: C02/0146

Silent remover and installer press with adapters for Movano, Master, Nissan

Press with bushing sleeves for the top link of the swingarm of Opel Movano, Renault Master, Nissan Interstar. Universal press for extruding and pressing pins, metal-rubber sleeves, ball pins and many elements that are within the dimensions of the press.

Product code: C02/0145

Bushing and silent puller adapter set for VW T4, LT, Sprinter, Movano, Master

Bushing and silent puller adapter set for VW T4, VW LT, Mercedes Sprinter, Opel Movano, Renault Master.

Product code: C02/0141

Hydraulic cylinder press for silents 12T

Press for extruding bolts and ball joints with a 12 ton press capacity.

Product code: C02/0136

Bushing and silent puller and installer for VW, Audi, Skoda, Seat

Bush puller for mounting the front control arm rear trailing bushes on VW, Skoda, Audi, Seat.

Product code: C02/0113

Front axle hub disassembly and assembly kit for Ford Transit (2000-)

The set is used to disassemble and assemble the front axle hub and bearings on Ford Transits manufactured after 2000.

Product code: C02/0108WF

Rear suspension bushing tool Renault Laguna II

Rear suspension bushing tool Renault Laguna II

Product code: W0047

Power steering pump puller

This tool facilitates the safe removal of the power steering pump.

Product code: W0430

Puller for removing and installing IVECO lower and upper pins after 2014

This specialized tool is designed to simplify the process of removing and installing lower and upper pins in IVECO vehicles manufactured after 2014.

Product code: W0651

Rear control arm bushing puller Ford, Volvo

Rear control arm bushing press and puller for Ford and Volvo. Puller and press tool for rear trailing arm bushes. The tool is used to assemble and disassemble bushings without the need to dismantle the swing arm. Threads should be lubricated with grease before use.

Product code: W0671

Suspension bushing puller, Opel Vectra B, BMW E36

Ideal for the removal and refitting of the suspension bushes without removing the trailing arm assembly from the vehicle.

Product code: W0001

Puller for suspension arm bushings, Cinquecento, Seicento

Puller for suspension arm silent blocks, Cinquecento, Seicento

Product code: W0004

Puller for plastic sleeves, Skoda Fabia, VW Polo

Puller for plastic sleeves, Skoda Fabia, VW Polo.

Product code: W0005

Sleeve puller, Golf IV, Audi A3, Skoda Octavia

Sleeve puller, Golf IV, Audi A3, Skoda Octavia

Product code: W0006

Puller for suspension arm mounting bushes in VW Golf III, Passat, Vento, Corrado

Puller for suspension arm mounting bushes in VW Golf III, Passat, Vento, Corrado. Only suitable for these models.

Product code: W0010

Press for silents and ball joints, for VW T4, Mercedes Sprinter, VW LT

Press for mounting and removing silents in the suspension arm in VW T4, VW LT and Mercedes Sprinter 1999-2006 without having to remove the arm from the vehicle.

Product code: W0027

Puller for double-row wheel hub bearings

Puller for double-row wheel hub bearings. Mechanical kit to facilitate work with double-row front and rear axle bearings. The purpose of the puller is to safely remove this type of bearing from the wheel hub.

Product code: W0037

Adapters for press, puller for bolts, Renault Master, Opel Movano

Adapters for press, puller for bolts, Renault Master, Opel Movano. It cooperate with W0027 and W0045 presses.

Product code: W0046

Front arm bushing puller BMW E39

The Front Arm Bushing Puller BMW E39 is a tool designed to remove the front arm bushing from the BMW E39 model.

Product code: W0057

Sleeve puller for Mercedes rear suspension arm

The tool allows you to remove and install the rear axle sleeves quickly and safely and without removing the suspension arm and wheel hub.

Product code: W0080

Bushing puller for BMW E36, Z3, E46 rear suspension arms

Bushing puller for BMW E36, Z3, E46 rear suspension arms.

Product code: W0083

Puller for suspension arm sleeves – front, BMW E 39 M5

This suspension arm sleeves puller is specially designed for BMW E39 535i ;540i M5 ; BMW 7 E38 models. The tool helps technicians to remove the suspension bushing easily and safely without damaging surrounding parts or the bushing.

Product code: W0086

Silent block puller for BMW E38, E39, E60, E63, E65, E53, X5, Z8 passanger cars

Extractor for removing and fitting the silent block on the rear axle link arm on BMW passanger cars.

Product code: W0087

Rocker pin puller and press for T4, Master, Movano, Interstar, Sprinter, VW LT

Press for upper bolts T4, Master, Movano, Interstar and lower bolts Sprinter, VW LT

Product code: W0093

Sleeve puller, rear beams, BMW E39 sedan

The sleeve puller is used to remove and install the rear axle bushing.

Product code: W0096

Press, puller for bolts of suspension arm, front Master/Movano/Interstar

This tool has a combined press and puller function, which allows convenient and efficient handling of the suspension arm pins. With the press function, the tool is able to press or unpress the pins from the rocker arms, ensuring accurate and stable pin insertion or removal.

Product code: W0097

Adapters for press, puller for bolts, Master, Movano, Interstar

Adapters for press, puller for bolts, Renault Master, Opel Movano, Nissan Interstar

Product code: W0098

Universal press for bolts and sleeves

Universal, strengthened press for bolts and sleeves of trailing arms.

Product code: W0099

Press, puller for bolts of suspension arms Opel, Renault, Nissan

Press, puller for upper and lower ball bolts of the suspension arms in Master, Movano, Interstar.

Product code: W0100

Puller screw, M12, 250mm

Screw for bushing and sleeve pullers, M12, 250mm.

Product code: W0101

Adapters for press, puller for bolts, Master, Movano, Interstar

Adapters for press, puller for bolts, Renault Master, Opel Movano, Nissan Interstar

Product code: W0102

Sleeve puller, rear beams FIAT Panda 2003-

Suitable for disassembling and assembling the bushings on the car for FIAT Panda models after 2003.

Product code: W0107

Puller for rear beam sleeve, BMW E39 touring

The tool precisely fits the rear suspension bushings of the BMW E39 Touring and can be used to easily remove and install the bushings without damaging the components.

Product code: W0113

Puller for rear beam sleeve, Ford Fiesta, Ka

Puller for rear beam sleeve is a specialized tool designed for Ford Fiesta and Ka models. This puller is an essential accessory for removing the rear beam sleeve, facilitating efficient and precise maintenance or replacement procedures.

Product code: W0114

Press for dismantling and mounting of lower bolts, IVECO

Press for dismantling and mounting of lower bolts, IVECO

Product code: W0115

Set of adapters for dismantling and mounting of lower bolts, IVECO

The adapter kit is precisely engineered and durable, and allows reliable and efficient removal and installation of lower suspension bolts. Designed to IVECO vehicle specifications to fit perfectly with the lower suspension bolts and allow smooth and safe operations.

Product code: W0116

Puller to the hub / bearings VW T5

Puller to the hub / bearings VW T5

Product code: W0129

Press, puller for bolts (W0027, W0102, W0116), Mercedes, VW, Opel etc.

Press, puller for bolts (W0027, W0102, W0116), Mercedes, VW, Opel etc.

Product code: W0133

Press, puller for bolts, strengthened (W0027, W0102)

Press, puller for bolts, strengthened (W0027, W0102) Mercedes Sprinter, Renault Master, Opel Movano, Nissan Interstar, VW T4. The set includes a press and a puller, which have a combined function. The reinforced design and durable materials ensure a reliable and long service life. The set contains the necessary accessories and adapters for different types of vehicles, so that it can be widely used during work.

Product code: W0134

Adapter for removing bolts VW Crafter, Mercedes Sprinter 906

Adapter for removing bolts in VW, Mercedes upper and lower control arms. The adapter is to be used with W0027, W0133, W0134 etc.

Product code: W0141

Sleeve puller for control arm rear axles for Fiat, Opel, Saab

Sleeve puller for control arm rear axles for Fiat, Opel, Saab

Product code: W0142

Wheel hub socket wrench Mercedes, inner diam.: 55mm

Wheel hub socket wrench Mercedes, inner diam.: 55mm.

Product code: W0146

Adapters for press, puller for bolts VW T4, LT, Mercedes Sprinter

The adapters allow the removal and installation of bolts in VW T4, LT and Mercedes Sprinter vehicles.

Product code: W0147

Plastic bushing puller for Skoda Octavia II, VW, Seat

Plastic silent puller for Skoda Octavia II, VW Touran, Golf IV, Jetta III, Golf V, Seat Ibiza IV, Toledo III. Sleeve OE: 6Q0 407 183.

Product code: W0155

Sleeve puller, rear beams Mercedes Benz S Class W / V 220 and C215 CL

The bushing puller is used to remove and install the rear axle bushing.

Product code: W0157

Sleeve puller, rear beams BMW E39 (sleeve oe no. 3317 1093 008)

The tool is used to press in and out the bushing number oe 3317 1093 008 in cars.

Product code: W0158

Press, puller for bolts Renault Master / Opel Movano

Press, puller for bolts Renault Master / Opel Movano + W0160 adapter

Product code: W0161

Press and puller for ball joints Renault, Opel, Iveco, VW, Nissan, Mercedes etc., 20 adapters

Universal press and puller for ball joints Renault, Opel, Iveco, VW, Nissan, Mercedes etc., with 20 adapters. For models manufactured in 2006 and on.

Product code: W0162

Hub Puller VW, Seat, Skoda-Puller with ABS and without ABS

The tool is suitable for removing the wheel hubs of both vehicles with and without ABS. Therefore, it can be widely used when servicing VW, Seat and Skoda models. The tool fits exactly on the hub and provides the right grip to pull the hub off efficiently and safely.

Product code: W0163

Upper control arm central bolt puller for VW, Audi after 2005

Upper control arm central bolt puller for VW, Audi after 2005.

Product code: W0164

Sleeve puller, rear beams BMW E39 (sleeve oe no. 3317 1090 389)

It's precisely designed to ensure the efficient removal of sleeves, particularly from the rear beams, making it an essential tool in preserving the integrity and performance of the vehicle's suspension and wheel assembly. Its compatibility with specific OE numbers guarantees accuracy and safety during the extraction process.

Product code: W0165

Universal puller small metal-rubber sleeve

Universal puller small metal-rubber sleeve. It is a perfect and ideal tool for effective and safe bushing removal.

Product code: W0167

Steering rod wrench

Allows the inner tie rod to be removed and installed without removing the rack.

Product code: W0168

Puller arm forward bushing Renault Laguna I

Puller arm forward bushing Renault Laguna I (nr. oe 77 00 824 042)

Product code: W0171

Sleeve puller, Golf IV, Audi A3, Skoda Octavia for the sleeve FEBI

Sleeve Puller designed specifically for Golf IV, Audi A3, and Skoda Octavia vehicles, compatible with FEBI sleeves. Ensures a precise and secure grip for effective removal.

Product code: W0172

Front, lower suspension bushing press for Opel Astra G, H, Zafira

Front, lower swing arm bushing puller for Opel Astra G , H , Zafira. Removes and installs silent blocks. OE: 352 364.

Product code: W0175

Rear beam bushing puller BMW E32 / E34 (nr. oe 3331112670)

When working on a BMW 5 Sedan (E34), BMW 5 Touring (E34) or BMW 7 (E32), the rear suspension bushing puller makes it easy to remove the bushings from the suspension. This tool provides the proper grip and power transfer to easily and safely remove bushings from the suspension.

Product code: W0181

Control arm bushing puller lower front Opel Astra G, H, Zafira, Vectra B

The control arm bushing puller for the lower front of Opel Astra G, Astra H, Zafira, and Vectra B is a specialized tool used to remove the control arm bushings in the front suspension of these vehicles.

Product code: W0190

Bushing puller Volkswagen T5, T6 rear arm

Silent puller for Volkswagen Caravelle, Multivan, Transporter rear arms. OEM: VW 7H0 501 131, VW 7H0 501 131 A, VW 7H0 501 132, VW 7H0 501 132 A

Product code: W0191

Puller front lower control arm bushings Fiat / Alfa Romeo / Citroen / Peugeot

Puller front lower control arm bushings Fiat / Alfa Romeo / Citroen / Peugeot

Product code: W0195

Bushing puller, Citroen C5

Silent puller, Citroen C5 (sleeve OE no. 352384)

Product code: W0196

Bushing press for Ford Focus, Mazda, Volvo

Press for extracting and installing rear axle bushings Ford Focus, Mazda 3 and 5, Volvo V50. OEM: 1061670, 98AG-5K896-AB.

Product code: W0230

Puller arm bushings front / rear, SEAT Leon, Toledo II, Skoda Octavia, VW Bora, Golf IV

The bushing puller is a tool for removing front and rear wheel hub bushings for SEAT Leon, Toledo II, Skoda Octavia and VW Bora, Golf IV models.

Product code: W0231

Puller arm bushings rear axle Ford Galaxy, Seat Alhambra, VW Sharan

Puller arm bushings rear axle Ford Galaxy, Seat Alhambra, VW Sharan (oe VW 7M0 407 181 A)

Product code: W0233

Puller sleeve rear beam (small) for BMW X5 E53, M57 etc.

Puller sleeve rear beam (small) (No. oe 33 17 6 770 457) for BMW X5 E53, M57, M57N, M54 etc

Product code: W0250

Puller sleeve rear beam (large) for BMW X5 E53, M57 etc.

Crafted to meet the exacting standards associated with BMW vehicles, this tool ensures precision and ease during maintenance or repair tasks.

Product code: W0251

Rear transverse upper control arm bushing puller (crescent / banana)

This tool allows for the mounting and dismounting of bushings on a car or with a hydraulic press.

Product code: W0254

Socket wrench for M52x1.5 Mercedes Vario rear hub nuts

Our Socket Wrench for M52x1.5 Mercedes Vario rear hub nuts is the perfect tool for unscrewing wheel hub nuts on the rear axle of your Mercedes Vario (1996-2013). With an OE code of 6743560126, this wrench offers precise and efficient performance. Get yours today!

Product code: W0338

Press / puller for removing and installing the rocker pin on Mercedes W124 cars

This press/puller tool is perfect for removing and installing rocker arm pin on Mercedes W124 W201 (190) models.

Product code: W0348

Rocker Arm Pin puller and press for Renault Scenic II; Grand Scenic II; Megane II; Dacia Logan

It is used for the disassembly and assembly of the wishbone pin at the front bottom of the vehicle.

Product code: W0352

Adapters for mounting and dismounting the front control arm bolts for Renault, Dacia

These adapters work with our universal press tool (W0099 - Universal press for bolts and sleeves). Adapters for mounting and dismounting the front control arm bolts.

Product code: W0353

Front hub nut wrench for Iveco Daily (2004-2019)

Front hub nut wrench for Iveco Daily (2004-2019).

Product code: W0354

Puller for wheel hub / bearing rear swingarm Mercedes Vito Viano 2.2 CDI after 2003

This puller is designed to safely and efficiently separate the wheel hub or bearing from the swingarm assembly.

Product code: W0361

Sleeve puller for Ford Mondeo MK 4 (2007- ), Volvo rear swingarm

Tool for assembly and disassembly of the sleeve without the need to disassemble the swingarm.

Product code: W0364

Rear beam sleeve puller Opel Zafira A; Astra G ; Combo ; Meriva A (oe number 402644)

This rear beam sleeve puller is designed to assist installing and removing bushings directly on the vehicle. Built to be compatible with various Opel models, it provides a tight fit and smooth operation, eliminating potential damage to the bushing or vehicle.

Product code: W0371

Rear control arm bushing puller for BMW

Rear control arm bushing puller for BMW E60, E61, E63, E64, E65, E53.

Product code: W0376

Puller arm bushing rear Fiat Bravo II (No.sleeves 50700796 )

This bushing puller is the ideal tool for the efficient and safe assembly and disassembly of rear control arm bushings on Fiat Bravo II cars.

Product code: W0377

Puller sleeve rear beam Renault Megane II; Scenic II; Grand Scenic II (oe sleeve 7701479190)

The Puller sleeve rear beam is a specialized tool to assist in the assembly and disassembly of rear beam bushings. This puller is specially designed for Renault Megane II, Scenic II and Grand Scenic II models.

Product code: W0379

Bushing puller for Ford and Volvo trailingarms

Bushing puller for Ford and Volvo trailingarms. Bushing OEM codes: 1566837, 1566837S1, 1865033.

Product code: W0385

Bushing installer press for Audi A4 Avant 94-01 rear beam (only for pressing)

Silent installer press for Audi A4 Avant 94-01 rear beam (only for pressing).

Product code: W0421

Puller arm sleeve Front Peugeot 406

This is a special tool that helps to stretch or remove the rocker arm bushing from the arm while minimizing the potential for damage and making the job easier.

Product code: W0422

Puller sleeves of rear beam / bridge Mercedes W210, W202, W203, W140 (OE 129 351 21 42)

The bushing puller is used to remove and install the rear axle bushing.

Product code: W0424

Puller of bushings of the front control arm Volkswagen T4

The puller is used to install and remove control arm bushings on the car.

Product code: W0427

Tool for mounting the hub booster pumps

Tool for installing wheel hub booster pumps. Due to the universal nature of the tool, it is compatible with many wheel hub sizes and types, so it can be used for many vehicles.

Product code: W0433

Bushing puller and press, front and rear axles BMW series 5, 6, 7

Silent puller and press for front and rear axles of BMW series 5, 6, 7.

Product code: W0444

Rear beam bushing puller for Mercedes S-Class (W220) CL-Class (C215)

The rear beam bushing puller is a specialized tool designed to remove the rear beam bushings from Mercedes-Benz S-Class (W220) and CL-Class (C215) vehicles. The rear beam bushings are essential components of the rear suspension system, and they help provide stability and control to the rear axle assembly.

Product code: W0453

Ball joint socket wrench for Renault Master III, Opel Movano B

Ball joint socket wrench for Renault Master III, Opel Movano B.

Product code: W0469

Rear beam sleevepuller for assembly and disassembly AUDI A4, A4 Avant 94-01

Tool for installing and removing rear beam bushings, especially for Audi A4/A4 Avant 94-01 models.

Product code: W0479

Puller sleeve rear beam Front Bmw Series 5,6,7 / F 10, F11, F12, 13, F01 (33316790573, 33 31 6 775 780)

This tool is a great help in installing and removing the bushing. Puller sleeve rear beam is a high quality tool specially designed for Bmw Series 5,6,7 / F 10, F11, F12, 13, F01 models. This tool fits the vehicle perfectly and guarantees perfect operation and durability.

Product code: W0488

Rear beam sleeve puller, Bmw Series 5,6,7 / F 10, F11, F12, 13, F01 (33 31 6775792, 33 31 6 793 864)

This puller helps you safely and efficiently remove the bushings that attach to the rear axle. The purpose of the tool is accurate and powerful removal, minimizing the risk of injury and facilitating service work.

Product code: W0490

Puller hub bearing the brake disc Ford Transit

The puller hub bearing the brake disc is a special tool used for mounting and dismounting brake disc bearings on Ford Transit vehicles.

Product code: W0500

Puller sleeve the arm forward (lower) L / R BMW X5 (E70) X6 (E71, E72), 3.0-4.8 (oe sleeve 31106778015)

The tool is used to remove and install the bushing sleeve without the need to disassemble the entire suspension system or remove the swing arm from the vehicle. It helps save time and effort during maintenance or repair procedures related to the front lower swing arm bushings.

Product code: W0501

Wrench for the front wheel hub nuts of Iveco 35 vehicles

Special key for mounting and dismounting the front hub nut of Iveco 35 vehicles. Inner diameter: 62.5mm.

Product code: W0502

Rear bushing puller BMW 1, 3, X1. BMW OE code: 33176760287, 33176760287

Rear silent puller BMW 1, 3, X1. OE codes: 33176760287, 20926439, 31471 0002, 26439, 51022, 6 760 287, FTR5226, 34643 01.

Product code: W0505

Puller hub / bearing Mondeo IV; Focus II RS (FORD 1 463 833)

This tool is designed for the assembly and disassembly of the front hub and bearing on Ford Mondeo IV and Focus II RS vehicles.

Product code: W0506

Puller sleeve for BMW bushings

Pulling tool for the assembly and thedisassembly of bushings on the car. BMW: 5 (E60), 5 Touring (E61), 6 (E63), 6 convertible (E64).

Product code: W0519

Puller sleeve back beam (middle) BMW 5 (E 60, E61) BMW 6 (E63, E64) (oem 33176770825)

This tool allows easy and safe removal of the center silencer from the rear beam without disassembling other components or the entire beam system.

Product code: W0520

Silent puller for VW, Audi, Seat, Skoda engines and gearboxes

Allows the replacement of engine and gearbox silent blocks in VAG engines.

Product code: W0521

Puller sleeve rocker back Fiat Doblo 2010-

It simplifies the process of removing and installing the rocker back assembly, contributing to the overall maintenance and repair of the engine's valvetrain system.

Product code: W0523

Short screw for bushing pullers M12, 150mm

This M12 short screw for bushing pullers is 150mm long and perfect for silent pullers. Get the job done quickly and efficiently with this durable tool.

Product code: W0530

Rear bushing puller for Opel Corsa B, C, Tigra

Rear silent puller for Opel Corsa B, C, Tigra. Opel OEM: 24443815, 5402636.

Product code: W0539

Wrenches for unscrewing / fixing shock absorbers (4 types )

The wrenches for unscrewing and fixing shock absorbers are specialized tools designed for specific applications. They are made of hardened and higher-grade materials to withstand the forces and torque required for working with shock absorbers. The wrenches are categorized by the size of the hexagon, and each size is suited for different car makes and models.

Product code: W0549

Front axle hub socket wrench for Suzuki Jimny, Vitara, Grand Vitara

Front axle hub socket wrench for Suzuki Jimny, Vitara, Grand Vitara. Diameter: 56mm, hexagonal drive.

Product code: W0562

Cap rear hub Ford Transit after 2014

This special installation tool is specially designed for Ford Transit vehicles for rear wheel nuts. The tool fits directly into the hub, allowing for accurate centering and locking in the hub.

Product code: W0574

Sleeve and silent puller for BMW 1, 3, X1 rear arms

Sleeve and silent puller for BMW 1 3, X1 Hatchback, Coupe, Convertible, Saloon, Touring rear arms. (OE 33326763092)

Product code: W0587

Bearing and silent puller for BMW rear axles

Extractor for the removal and installation of the ball joint bearing on the wheel support of the rear axle on BMW 1, 2, 3, 4, X1, X3, X4, i8 series.

Product code: W0627

Puller sleeve rear trailing arm KIA Creed I, II, Hyundai I 30 (oe sleeve 55543-2H000)

This tool allows accurate and safe removal and installation of the bushing in the rear longitudinal control arm.

Product code: W0643

Sleeve puller and press for rear control arms of Jeep Compass, Patriot, Dodge Caliber

Left and right side rear trailing arm bushing puller and press for Jeep Compass, Patriot, Dodge Caliber. Sleeve outer diameter: 70mm.

Product code: W0645

Opel rear axle bushing removal tool (OE: 4 02 952, 54 02 637)

Opel Astra H, Zafira B, Meriva B rear axle bushing removal tool (OE: 4 02 952, 54 02 637)

Product code: W0652

Bushing puller and press for Fiat, Opel rear arms

Silent puller and press for Fiat Doblo (2009 and on) rear arms.

Product code: W0658

Wrench for Iveco 35 front wheel hub nuts

This wrench is specifically designed to fit front wheel hub nuts with internal teeth and M50*1.5 thread dimensions.

Product code: W0664

Rear control arm bushing puller Hyundai, Kia

The rear control arm bushing puller Hyundai, Kia is a special tool used to install and remove rear steering linkage bushings on Hyundai and Kia vehicles. Rear steering link bushings are components that are found in the steering system and are important for stable steering and control of the vehicle.

Product code: W0668

Rear beam bushing puller Toyota YARIS 2005-2011

The rear beam bushing puller for Toyota YARIS 2005-2011 is a specialized tool designed specifically for pressing rear beam bushings onto the car's rear suspension.

Product code: W0669

Rocker Arm Pin puller and press for Renault Scenic II, Clio III;

It is used for the disassembly and assembly of the wishbone pin at the front bottom of the vehicle.

Product code: W0670

Rear beam bushing puller Ford Fiesta V, MK5; Fusion; Mazda 2 (Febi 27245; Ford 1 426 699)

The Rear Beam Bushing Puller is a specialized tool designed for the assembly and disassembly of rear beam bushings in Ford Fiesta V (MK5), Fusion, and Mazda 2 vehicles. This tool is specifically engineered to simplify the process of removing and installing rear beam bushings.

Product code: W0705

Front swing arm bushing puller VOLVO S60 I, S80 (TX, XY), V70 I and II

This tool is meticulously designed for the installation and removal of front swing arm bushings in VOLVO vehicles.

Product code: W0482

Press for bushings and silents for hydraulic cylinder 12T

Press for pins and bushings without adapters. Can be used with a hydraulic cylinder.

Product code: C02/0149

The wrench for the side pressing nut of the Mercedes steering rack

This tool is ideal for professionals and DIY enthusiasts alike, this tool ensures seamless installation, removal, and adjustment of the steering gear side pressure nut.

Product code: W0728

Wrench for BMW & Mercedes Steering Gear Side Nut

This is a dedicated wrench, purposefully designed for the assembly, disassembly, and adjustment of the side nut in BMW and Mercedes steering gears.

Product code: W0729

Ball joint separator set, 3pcs

Ball joint separator designed for removing the track rod end from the steering arm without doing damage to the taper pin. Suitable for most small cars and light vans.

Product code: DK-230503

Rear Control Arm Bushing Puller for Fiat Bravo II

The rear control arm bushing puller is designed specifically for removing the rear control arm bushing on a Fiat Bravo II without the need to remove the control arm from the car.

Product code: W0378

Socket / wrench for unscrewing the hub nut Land Rover DEFENDER 1999-2016

This tool is for unscrewing the hub nut on Land Rover Defender (1999-2016), compatible with VIN starting from XA159807. Part number: RFD100000.

Product code: W0642

Steering Rack Side Nut Wrench for Daewoo, Opel and Saab models

This specialized wrench is designed for quick and efficient installation or removal of steering rack side tightening locknuts.

Product code: MS00013

Wrench for upper nut of worm gear steering rack for Toyota models

Specialized nut socket for efficient and safe installation/removal of the upper nut of the worm gear in steering racks, compatible with select Toyota (Avensis, Echo, Prius, Vitz, Yaris) models.

Product code: MS00026

Oil seal installer tool for hydraulic cylinder

Professional tool for precise installation of oil seals into the hydraulic cylinder and rack mechanism of steering systems. Universal tool for all car models.

Product code: MS00030

Wrench for upper nut of worm gear steering rack for Toyota Corolla 2002-2007

Specialized nut socket for efficient and safe installation/removal of the upper nut of the worm gear in steering racks. Suitable for Toyota Corolla (2002-2007).

Product code: MS00031

Wrench for bottom nut of worm gear steering rack

Durable and precise tool for mounting and dismounting the bottom nut of worm gear steering racks, ensuring the nut remains in excellent condition. Compatible with multiple car models.

Product code: MS00032

Steering Rack Side Nut Wrench for Nissan and Samsung models

Specialized tool for easy and safe installation, removal, and adjustment of the steering rack side tightening nut. Designed to prevent nut damage and ensure smooth maintenance for various Nissan models and Samsung SM5 (A32).

Product code: MS00034

Steering Rack Side Nut Wrench for Mitsubishi L200

Specialized tool for mounting, dismounting, and adjusting the steering rack side tightening nut. Designed for Mitsubishi L200 models, ensuring precise and damage-free maintenance.

Product code: MS00037

Set of fitting for testing power steering rack on the test bench

A universal set of fittings for securely connecting a steering rack to a test bench during diagnostics. Includes fittings and clamping plates to minimize mechanical damage, even in heavy-duty operations.

Product code: MS00553

Steering gear lock nut removal tool for Mercedes- Benz S-Class (W140)

Specialized tool for safe and efficient removal of the steering gear lock nut in Mercedes-Benz S-Class (W140) models, protecting the lock nut from damage.

Product code: MS00048

Fitting for testing power steering pump on a test bench for Mercedes-Benz S-Class and SL models

A fitting for securely connecting power steering pumps to a test bench for diagnostics, compatible with Mercedes-Benz S-Class (W221), S-Class Coupe (C216), and SL (R230).

Product code: MS00062

Steering rack bushing tool for Toyota Avalon, Camry

Specialized nut socket for safe installation and removal of steering rack bearing bushings, compatible with Lexus ES and Toyota Avalon and Camry models.

Product code: MS00065

Wheel hub puller set

Wheel hub puller set, suitable for VW, Audi, Alfa Romeo, Ford, Citroen, Bmw, Mazda, Fiat, Mercedes-Benz, Seat, Opel, Peugeot, Renault, Skoda, Porsche

Product code: MG50438A

Axial joint puller 28-35mm

Suitable for quick and easy removal/installation of the steering knuckle. Clamping size 28-35mm, length 400mm, hexagon end 27mm (1/2"DR)

Product code: MG50045A

Wishbone lever tool

Wishbone lever tool, Length: 1180mm, Tube: Ø 3.5cm, Brace distance: 50 - 45 - 40 - 35 - 30cm, Fastening support: 15 x 13cm

Product code: JBM51902

Wishbone lever tool, sliding type, lockable at 5 points

The device helps to ensure that the swingarms are stably and securely fixed, only they are maintained or installed.

Product code: MG50417

Suspension support rod measuring tool

The device is designed for precise measurements of the curvature of the front suspension support pipes. Dial indicator not included.

Product code: C06/0212

Rear axle nut wrench for Renault, Nissan, VW, Opel, Mercedes

For loosening the groove nut on rear wheel hubs. OEM codes: T50017, CH50112, 906589000700, 8201079089

Product code: W0608

Puller for front control arm pins of Renault Master, Opel Movano

Puller for front control arm pins of Renault Master, Opel Movano

Product code: W0045

Adapter for mounting pin BMW 3 and Z 3 (BMW E36) BMW 31126758510

The Adapter for Mounting Pin BMW 3 and Z3 is a specialized tool designed to facilitate the precise installation or pressing of pins in BMW 3 Series and Z3 models. This adapter is specifically designed to work with a hydraulic or manual press, ensuring a secure and accurate pin installation process.

Product code: W0707

Socket wrench key for Citroen and Peugeot swingarms

Socket wrench key for Citroen Berlingo, C4 and Peugeot 307, 308, 5008 swingarms.

Product code: W0362

Steering Knuckle Nut Wrench for Mercedes Actros, Axor, Antos, Arocs

This wrench is designed for unscrewing the steering knuckle nut of specific Mercedes trucks. It offers a precise fit and is compatible with both OEM and certain aftermarket parts.

Product code: W0735

Rocker Arm Nut Wrench for Iveco Daily 2006 E4

This tool is specifically tailored to unscrew the nut of the rocker arm.

Product code: W0734

Wrench for the front swingarm pivot pin caps on Citroen, Peugeot, Toyota

Socket wrench for the front swingarm pivot pin caps on Citroen (Jumpy, SpaceTourer), Peugeot (Expert, Traveller), Toyota (Proace) suspensions. 2016 and on.

Product code: W0577

Kingpin adapters for crossovers Jeep - Cherokee, Grand Cherokee, Wrangler

Our set of 4 adapters is designed to simplify the mounting and dismounting of kingpins without the need to remove the steering knuckle.

Product code: W0312

Camber angle setting tool

A useful tool for adjusting the angle of the wheel, mounted between the rim and the body. Correct wheel angle adjustment is important for vehicle handling, steering and wheel wear.

Product code: W0183