New products

3pcs hose clip pliers

Hose clamp pliers set, 3 pcs, Easy to apply in hard-to-reach places, Protects the hoses from damage, Angle: 90°

Product code: JBM53395

52pcs radio release tool kit

Wrenches, hooks, suitable for Kenwood 1998-2001, Sony II 2002, Kenwood III 2002, Pioner + JVC, Sony I 2001, Sony Idic 2005, Panasonic 2006, Kenwood I 1998, Kenwood Mask, Blaupunkt, Grundig

Product code: JBM53388

Piston ring compressor 3", 53-175mm

3" piston ring compressor. Ø 53/175mm

Product code: JBM52696

Piston ring compression set

Piston ring service tool set for install piston rings; 3 pcs piston ring plates/compressors; 1 piston ring expander; Piston ring groove cleaner; 3 blades

Product code: JBM53251

Extendable flexible tip with 4 claws

Extendable flexible tip with 4 claws, total length 500mm, max. jaw opening 20mm.

Product code: JBM51526

Set of 1/4” extension bars with round end

Set of 1/4” extension bars with round end, Measurements: 50mm, 75mm, 100mm, 152mm, 227mm.

Product code: JBM51805

Telescopic magnetic pick-up tool

Telescopic magnetic pick-up tool, length 135 - 600mm, magnet capacity: up to 2.5kg.

Product code: JBM52472

Universal press and pull sleeve kit, 34-82mm

Spindle: M10, M12, M14, M16, M18, Adapters (Outer/inner diameter): 74/54mm, 76/56mm, 78/58mm, 72/52mm, 70/50mm, 68/48mm, 80/60mm, 82/62mm, 66/46mm, 64/44mm

Product code: JBM52494

Battery hydrometer

Hydrometer to measure the state of charge in batteries.

Product code: JBM53209

Drain plug wrench

Drain plug wrench. Square heads 8mm and 10mm. For vehicles Citroën, Renault, Peugeot.

Product code: JBM52617

Transmission fluid and engine oil level gauge (dipstick) set, Mercedes Benz/Audi

5pcs transmission fluid and engine oil level gauge (dipstick) set for vehicles Mercedes Benz and Audi. Length: 920 - 930 - 1160 - 1200mm.

Product code: JBM53206

Flask with flexible neck 5l

Plastic flask with flexible neck, 5l

Product code: JBM52992

Screwdriver set with interchangeable handle 20-in-1

Screwdriver set with interchangeable handle 20-in-1. Straight (4-7), Phillips (1-2), Pozidriv (1-2), Hexagonal (4-6), Hexagonal tamper proof (4-6), Torx (T10-40)

Product code: JBM53010

6 pcs parallel pin punch set

6 pcs parallel pin punch set; Sizes: Ø3, 4, 5 ,6 ,7, 8mm; Lenght: 150mm; Metal box

Product code: JBM53095

Clutch centering mandrel, 2pcs

2pcs clutch centering mandrel, Ø20-26mm, Ø15-19mm

Product code: JBM53392

Engine timing tool Audi & Škoda

Engine timing tool Audi, VW & Škoda. For vehicles Audi / VW V6 2.0 - 2.8 - 3.0T FSI , Audi Q5 2.0 - A6L 2.8 - 3.0T

Product code: JBM53276

Audi VW enging timing tool set V6 2.0/2.8/3.0 TFSI

Audi - VW enging timing tool set. For vehicles Audia A2, A3, A4, A6, A8 with motor V6 2.0/2.8/3.0 TFSI

Product code: JBM53278

180° tube bender 1/4" (6mm), 5/16" (8mm) and 3/8" (10mm)

Tube bender. Diameter range: 1/4" (6mm), 5/16" (8mm) and 3/8" (10mm). For aluminum, copper and steel tubes. 0-180° angles.

Product code: JBM52905

Auto fuse assortment, 48pcs

48pcs auto fuse assortment, 8pcs 5A, 8pcs 10A, 8pcs 15A, 8pcs 20A, 8pcs 25A, 8pcs 30A

Product code: JBM53367

Oil extractor hand pump

Oil extractor hand pump with a flexible tube. Capacity 200 ml.

Product code: JBM52628

Injector copper ring assortment, 551pcs

551pcs injector copper ring assortment for vehicles Mercedes, Renault, Iveco, Ford, BMW, MAN, Mazda, Land Rover, Deutz, Fiat, KIA and Universal washers

Product code: JBM53464

Windshield wiper puller

Windshield wiper puller, max. diameter 45mm, min. diameter 17mm, simple handling, safe mechanism, design with thin legs and brass-finished ends. Weight 0.2kg.

Product code: JBM52454

Flexible screwdriver

Flexible screwdriver with 3 sockets. Drive 1/4". Sizes 4, 5, 7mm. Length 500mm.

Product code: JBM53575

Breaker bar 1/2" 600mm

Breaker bar, high resistance and durability, drive head 1/2", length 600mm, 180º flexible head, handle material: Acero 40CR

Product code: JBM52526

Leak tester for cylinder head gasket

CO2 Combustion leak detect. This tool is designed to check for the leaks between combustion and cooling system of water-cooled engines. With 3 adapters.

Product code: JBM53662

1/2" breaker bar replacement head

1/2" breaker bar replacement head

Product code: JBM11945

Wishbone lever tool

Wishbone lever tool, Length: 1180mm, Tube: Ø 3.5cm, Brace distance: 50 - 45 - 40 - 35 - 30cm, Fastening support: 15 x 13cm

Product code: JBM51902

Magnetic protector cover fins and fronts

Magnetic protector cover fins and fronts, Measurements 110x64cm, 4 magnetized points, Two faces: One velvet

Product code: JBM51622

1/4" short, hinged 72-teeth ratchet

1/4" short, hinged, 72-teeth reversible ratchet.

Product code: JBM51306

113 pcs auto vacuum connector assortment

113pcs auto vacuum connector assortment. This assortment of vacuum connectors can be used to connect or split vacuum lines or other hoses of a variety of diameters.

Product code: JBM53910

1/2" short hinged 72-teeth ratchet

1/2" short hinged 72-teeth reversible ratchet.

Product code: JBM51305

Windshield removal tool (T handle)

Windshield removal tool (T handle)

Product code: JBM13814

Angle impact wrench 1/2"

1/2" Angle impact wrench, Jumbo hammer system, Working torque range: 27-231Nm, Free speed: 8.500RPM, Air inlet: 1/4"

Product code: JBM53733

Anti-freeze tester

Anti-freeze tester, Measuring range: -43ºC to 131ºC

Product code: JBM53453

208 pcs bit set

208 pcs bit set. 25, 50, 75mm bits, hexagonal sockets and adaptors.

Product code: JBM53574

Heating tube assortment, 127pcs

127pcs heating tube assortment, 30pcs M2x40, 25pcs M2.5x40, 20pcs M3.5x40, 20pcs M5x40, 16pcs M7x80, 8pcs M10x80, 8pcs M13x85

Product code: JBM53374

Mini fuse assortment, 50pcs

50pcs mini fuse assortment, 8pcs 5A, 8pcs 10A, 8pcs 15A, 8pcs 20A, 8pcs 25A, 10pcs 30A

Product code: JBM53368

Metric grease fitting assortment, 110pcs

110pcs metric grease fitting assortment, M6x1, M8x1.25, M10x1.5, angle 45°, 90°, 180°

Product code: JBM53359

Auto fuse assortment, 120pcs

120pcs auto fuse assortment, 20pcs 5A, 20pcs 10A, 20pcs 15A, 20pcs 20A, 20pcs 25A, 20pcs 30A

Product code: JBM53356

Copper washer assortment, 110pcs

110pcs copper washer assortment, M6, M8, M10, M12, M14, M16

Product code: JBM53353

Injector copper ring assortment 375 pcs

375pcs injector copper ring assortment. For sealing of e.g. injectors on Common-Rail Diesel injection systems (CDI). Material: T2 copper

Product code: JBM53340

Engine timing tool set renault Opel 2.2/2.5 TDi DCi

Timing tool set for Opel, Nissan, Dacia, Renault. 2.2, 2.5 DCI, DTI Renault, 2.2 16V petrol engines.

Product code: JBM53292

Injector copper ring assortment 150 pcs

150pcs injector copper ring assortment. For sealing of e.g. injectors on Common-Rail Diesel injection systems (CDI). Material: T2 copper

Product code: JBM53229

6pcs Trim pad removal tool kit

6 lever set, Sizes: 5”x8.5mm, 5”x10.3mm, 5”x4.5mm, 15”x8.5mm, 15”x10.3mm, 15”x4.5mm. The door trim removes the patents simply and without damaging them.

Product code: JBM53110

Swivel jaw band clip pliers

Swivel jaw band clip pliers

Product code: JBM13708

8 pcs short ratcheting combination wrench set

8 pcs short ratcheting combination wrench set. Sizes: 10, 11, 12, 13, 14, 15, 17, 19mm

Product code: JBM53022

Plastic rivet assortment (150 pcs)

Plastic rivet assortment. Contents: 25pcs - 6 x 19.3mm, 25pcs - 6 x 17.8mm, 25pcs - 6 x 25.5mm, 25pcs - 6 x 24.5mm, 25pcs - 6 x 24mm, 25pcs - 6 x 24mm

Product code: JBM52711

Extensible extractor magnetic with LED

Magnetic extensible extractor, with LED, length: 545mm.

Product code: JBM52473

Telescopic inspection mirror

Telescopic inspection mirror, length 280 - 445mm, mirror diameter 50mm.

Product code: JBM52468

1/2” extendable hinged ratchet

1/2” extendable, reversible 72-teeth socket wrench with hinged head.

Product code: JBM52197

Gas Torch

Gas torch with adjustable flames. Reaches up to 1300 °C.

Product code: JBM51920

Dent tool kit

Automotive body dent repair set, with slide hammer and puller. For quick body repairs without damaging the paint and metal.

Product code: JBM53224

Radio removal tool set

Radio removal tool set, 20pcs

Product code: JBM51126

6 pcs type "S" wrench set 12 points (Eva tray)

6 pcs type "S" wrench set 12 points (Eva tray). 8-9, 10-11, 12-13, 14-15, 16-17, 18-19mm

Product code: JBM15160

Headlight restoration kit

The JBM liquid polymer headlamp refurbishment kit is an innovative system for restoring sunburnt headlamps to their original condition, with the original gloss and a perfect finish in a very fast and economical way.

Product code: JBM53673

3piece set of 1/2" impact socket - special wheel removal

3piece set of 1/2" impact socket with plastic cap, special wheel removal, size: 17-19-21mm, length 85mm

Product code: JBM51336

Pump oiler 0.25l

Pump oiler with 0.25l tank

Product code: JBM52243

Pneumatic grinder set - 16-pieces

16-pieces pneumatic grinder set, composite engine, air connection 1/4", max. speed 25000rpm, max. pressure 90PSI / 4CFM

Product code: JBM52157

1/2" ratchet impact wrench, 61Nm

1/2" ratchet impact wrench, reversible, max. torque 61Nm, air connection 1/4", Max. pressure 90 PSI / 5CFM, Rotation speed 150rpm

Product code: JBM52167

Valve caps and valve core set

Valve caps and valve core set. Contents: 16pcs aluminium caps for valve tire, 50pcs green plastic caps for valve tire, 50pcs black plastic caps for valve tire, 50 units valve core set, 50pcs valve core set high pressure, 1pc core puller

Product code: JBM52673

Timing tool set for Opel, Suzuki 1.0, 1.2, 1.4

Timing tool set for Opel, Suzuki 1.0, 1.2, 1.4 petrol engines with timing chain.

Product code: JBM53301

Circlip plier set with changeable tips

Circlip plier set with changeable tips. (90º,45º,15º,0º)

Product code: JBM53389

Transmission oil filling system (ATF)

Transmission oil filling system. Capacity: 7.5l, Outlet: 80cc cycle, Viscosity range up to SAE140. Includes 15 accessories for Ford 1/8 - 27, universal BMW, Honda, Nissan, VW, Audi, Skoda, Porsche, Mini Cooper, Mercedes, Hyundai. Universal and flexible 300mm hose.

Product code: JBM52797

Oil extractor pump - 12V

Oil extractor pump 12V. Useful for motor oil, diesel or heating oil.

Product code: JBM53566

Piston ring compressor 6", 60-175mm

6" piston ring compressor. Ø 60-175mm

Product code: JBM52697

Suction cup pullers

Suction cup pullers. With ratchet straps (5m x 25mm)

Product code: JBM52998

Seal and plug removal hook set

Seal and plug removal hook set. 3 pcs. (15.5, 16.5, 12cm)

Product code: JBM53053

Diesel dispenser pump with gun (550W)

Portable electric fuel transfer pump. Hose lenght: 2m / 4m. Head: 10m.

Product code: JBM53610

Combustion leak tester fluid

Combustion leak tester fluid

Product code: JBM14563

Set of hinged Torx socket wrenches

Set of double hinged Torx socket wrenches. 4 pcs. E6 - E24.

Product code: JBM50622

Case with 6 hinged 12 point socket wrenches

Case with 6 hinged 12 point socket wrenches. 8-9, 10-11, 12-13, 14-15, 16-17, 18-19mm

Product code: JBM51659

6 pcs impact adapters

6 pcs impact adapters, sizes: 1/2"F x 1"M (length: 50mm), 1/2"F x 3/4"M (length: 48mm), 3/4"F x 1"M (length: 63mm), 3/4"F x 1/2"M (length: 85mm), 1"F x 3/4"M (length: 69mm), 1"F x 1/2"M (length: 70mm)

Product code: JBM52544

Set of 12 short, flexible ratchet ring spanner set

Set of 12 short, flexible ratchet ring spanner set. Sizes: 8 - 19mm.

Product code: JBM54032

Oil drain plug socket set of 23pcs

23pcs Oil drain plug socket set. Oil drain plug socket set, ideal for most car and van oil drain plugs. The case includes several accessories of different sizes.

Product code: JBM53735

Flexible ratcheting combination spanner set

7 pcs flexible ratcheting combination spanner set. Sizes: 8 - 19 mm

Product code: JBM15158

Diesel dispenser pump with gun (12V)

Portable fuel transfer pump. Car battery powered. 45 L/min.

Product code: JBM53609

4 piece set of 1/2" impact sockets for alloy wheels

4piece set of 1/2" impact socket with plastic cap, special wheel removal, size: 17-19-21-22mm, length 85mm

Product code: JBM52338

Clutch centering mandrel, 11pcs

11pcs clutch centering mandrel with accessories, Ø20-26.6mm, Ø15-19mm, Ø23-36mm, Accessories diameters: 12, 14, 15, 16, 17, 18, 19, 20mm

Product code: JBM53410

4pcs dent pulling circular tabs

Used widely for automobile, refrigerator, motorcycle, washing machine, etc. dent repairs.

Product code: JBM13843

10pcs dent puller tabs. Oval, circular and rectangle shapes.

Used widely for automobile, refrigerator, motorcycle, washing machine, etc. dent repairs.

Product code: JBM13844

Headlight restorative liquid 600ml

Restores the original color and texture of the headlight. Use after polishing.

Product code: JBM15375

Engine Timing Tool Set - BMW 2.0D N47/N47S/N57/N57S C01/0194

Product code: C01/0194

Renault, Nissan timing lock 1.6 DCI

Timing lock set for Renault, Nissan 1.6 DCI, R9M.

Product code: C01/0200

Timing lock for Opel, Chevrolet 2.0d VCDi SOHC diesel belt

Timing lock for Opel, Chevrolet 2.0d VCDi SOHC diesel belt.

Product code: C01/0218

Jaguar and Land Rover timing tools set for JLR 2.0 Diesel AJ200 engines

Jaguar and Land Rover timing tools set for JLR 2.0 Diesel AJ200 engines. The kit contains all the essential components required to lock the new JLR 2.0L “Ingenium”.

Product code: C01/0219

Timing tool set for Jaguar and Land Rover (V8 5.0)

The timing tool set enables the set up of correct the engine timing when replacing the timing belt.

Product code: C01/0220

Timing lock for BMW and Mini B37, B47, B57 1.5, 2.0, 3.0 diesel engines with chains

Timing lock for BMW and Mini B37, B47, B57 1.5, 2.0, 3.0 diesel engines with chains.

Product code: C01/0223

Engine timing tool set for BMW, Mini (B38, B46, B48)

This engine timing tool set was specially designed for new generation BMW and Mini chain driven B38, B46 and B48 engines since 2014.

Product code: C01/0225

Timing Lock for BMW N63, S63 4.4L V8 С01/0227

Product code: C01/0227

Timing lock for Opel engines 1.3 CDTi

A set of tools for setting, adjusting and locking the engine timing on the latest 1.3 CDTi (2015-2018) diesel engines in Opel cars.

Product code: C01/0228

Timing lock set for Ford 1.0 EcoBoost (Fox) LT

Ford timing lock for 1.0 Eco Boost (Fox) LT engines from 2018.

Product code: C01/0229

Engine timing kit for Hyundai, Kia 1.6 Diesel engines

Engine timing kit for Hyundai, Kia 1.6 CRDi, D4FE, D4FE (U3) Diesel engines.

Product code: C01/0231

DSG Clutch Removal Kit for VW Group C05/0213

DSG Clutch Removal Kit for VW Group C05/0213

Product code: C05/0213

Crankshaft rear oil simering tool for Iveco, Fiat Ducato 2.3 engines

Gasket replacement tool - Rear crankshaft simering tool for Iveco, Fiat Ducato 2.3

Product code: C05/0216

Pneumatic portable jack 22t

Designed for heavy duty truck, bus and trailer shop use. It is also portable so it can be used for roadside service calls.

Product code: G01068

Hydraulic jaw puller set 20t

Multi-function puller with adjustable two or three leg function. Allows bearings, gears, etc. to be easily removed with minimal effort by use of the hydraulic puller.

Product code: G00912

Crimping pliers set 3pcs, 90° bended

Set of bent crimping pliers for flexible hoses. For hoses up to 63.5mm in diameter. The pliers can be used to prevent liquids from flowing out of cooling pipes, brake pipes, etc.

Product code: G00926

Diesel fuel hand pump with 2x1m hoses

Ideal for introducing fuel into the fuel pump after replacement of the fuel filter.

Product code: G00991

Pistol and lever grip grease gun. Capacity: 400ml

Lever/Pistol Grip Grease Gun 400cc

Product code: G01128

Oil suction gun. Capacity: 500ml

Oil suction gun is suitable for removing or replacing oil in engines and gearboxes.

Product code: G01150

Oil suction gun. Capacity: 1000ml

Oil suction gun is suitable for removing or replacing oil in engines and gearboxes.

Product code: G01151

Handheld vacuum tester and brake bleeding kit

Professional vacuum and pressure diagnostics tool used to test a variety of essential engine and associated functions including fuel, ignition, transmission and emissions.

Product code: G01156

Digital tire tread depth gauge 0 - 25,4mm

Digital depth gauge ideal for checking the tread depth of tires.

Product code: G01269

Dial type tire air pressure gauge 10-100psi

Solution for measuring tire pressure on all kind of vehicles. Maintaining proper tire pressure reduces fuel consumption and maximizes tire tread life, making your tires last longer and perform better.

Product code: G01304

CV boot clamp pliers (ear type)

CV boot clamp pliers suitable for Oetiker CV drive shaft boot securing clips. Plier's plate presses a flat on the top of the clip so that it forms the spring loop correctly.

Product code: G01656

Fuel feed pipe pliers

Suitable for the removal of connectors on in-line fuel filter.

Product code: G01659

Circlip pliers set 8" (200mm)

Circlip pliers set 8" (200mm) includes pliers with straight tips and angled tips for internal and external circlips

Product code: G01662

Circlip pliers set 10" (250mm)

Circlip pliers set 10" (250mm) includes pliers with straight tips and angled tips for internal and external circlips

Product code: G01663

Long Torx key set T10-T50 9pcs

Long Torx key wrench set T10-T50. Set includes 9 pieces of long Torx key wrenches: T10, T15, T20, T25, T27, T30, T40, T45, T50.

Product code: G01705

Ramps set 2pcs for cars up to 2t

Universal ramps for cars. Made of durable plastic. Perfect for home garages.

Product code: G02043

Cutter for tire repair. Diameter 4.5mm

It is designed for cleaning and enlarging holes on punctured radial and diagonal tires.

Product code: 511-1345

Tool holder (shank), for tools with 3/8" x 12mm thread

Tool holder (shank), for tools with 3/8" x 12mm thread

Product code: 519-6610

Tool holder (shank), M14 x 11mm, for tools with 76mm and 102mm diameters

Tool holder (shank), M14 x 11mm, for tools with 76mm and 102mm diameters

Product code: 519-6634

Tool holder (shank), for tools with 8mm shank

Tool holder (shank), for tools with 8mm shank, Buffing tool accessory.

Product code: 519-6689

Pick with a wooden handle. Lenght: 140mm

It is helpful when inspecting tire damage before and after machining.

Product code: 570-9270

Coconut fibre brush

The coconut fibre brush enables the safe removal of rubber abrasion from the roughened rubber of the tire.

Product code: 594-0000

K80 buffing band with a shaft. Size: 60x30mm

A flap wheel designed to remove outflows during the cosmetic treatment of vulcanized places in thermopresses.

Product code: 594-0830

Steel brush, 60mm diameter

Designed for roughening rubber on the outside and inside of all types of tires.

Product code: 595-0076

Buffer stone (flat). Diameter: 40mm

The 40 x 10mm stone is suitable for machining steel cords during tire repair.

Product code: 595-0650

Pressure roller for tires. Width: 4mm

The 4mm wide bearing roller with a diameter of 35mm combined with a wooden handle makes up a pressure roller useable during tire repair.

Product code: 595-1044

Tool holder (shank), Diameter: 8mm, for tools with 3/8 thread

The 8mm tool holder is a shank that allows tools to be securely clamped during the tire repair process into devices (drills for example).

Product code: 595-4034

PVC coated steel wire buffer. Diameter and height: 76mm x 20mm

PVC coated steel wire buffer with a diameter and height of 76 x 20mm and a bore of 14mm is intended for roughening rubber on the inner side of all types of tyres.

Product code: 595-4175

K36 dome rasp wheel. Diameter and height: 76x32mm

The K36 dome rasp wheel with a diameter of 76mm and a 14mm hole is designed for roughening the inside of lorry, agricultural and oversized vehicle tires.

Product code: 595-4209

Carbide rasp wheel. Diameter: 65mm

The carbide K46 rasp wheel with a diameter of 65mm is designed for roughening the insides of any car tires.

Product code: 595-4216

Rotary gouge for drills. Diameter: 50mm

The rotary gouge with a diameter of 50mm is designed for removing large amounts of rubber from the damaged outside areas of lorry, oversized and agricultural vehicle tires.

Product code: 595-4292

Buffing stone (cone). Diameter x length x mandrel diameter: 7 x 25 x 6mm

The 7 x 25mm stone is suitable for machining steel cords during tire repair.

Product code: 595-4405

Buffing stone. Diameter x mandrel diameter 32x6mm

The 32 x 6mm stone is designed for machining steel cords during tire repair.

Product code: 595-4412

Tire scraper

Tire scraper is particularly suitable for profiled surfaces. Allows for the pre-cleaning of the inside and outside of a all types of tires.

Product code: 595-4515

Brass wire brush

The brass wire brush is designed for cleaning mechanically roughened surfaces from the finest particles of rubber abrasion.

Product code: 595-4553

Cutter. Diameter x length: 3x50mm

Durable cutter designed to expand the hole on the damaged tire usable during repairs with inserts or pins.

Product code: 595-4900

Cutter for tire repair. Diameter x length: 6 x 65mm

Durable cutter designed to expand the hole on the damaged tire usable during repairs with inserts or pins.

Product code: 595-4924

Drum sander. Diameter x height: 75 x 30mm

The buffing drum with a diameter of 75mm is designed for the cosmetical removal of outflows caused by thermopresses

Product code: 595-5552

Cutter for tire repair. Diameter x lenght: 4.5mm x 90mm

Durable cutter designed to expand the hole on the damaged tire usable during repairs with inserts or pins.

Product code: 595-5019

Cutter for tire repair. Diameter x lenght: 10mm x 110mm

Durable cutter designed to expand the hole on the damaged tire usable during repairs with inserts or pins.

Product code: 595-5060

K60 buffing band. Diameter x height: 45 x 30mm

The K60 buffing band with a diameter of 45mm is designed for the cosmetical removal of outflows caused by thermopresses.

Product code: 595-5514

K60 buffing band. Diameter x height: 75mm x 30mm

The K60 buffing band with a diameter of 75mm is designed for the cosmetical removal of outflows caused by thermopresses.

Product code: 595-5569

Pencil rasp. Diameters and lenght: 5x8mm -105mm

The K18 pencil rasp with diameters of 5 x 8mm is designed for roughening rubber on the outside of car and lorry tires.

Product code: 595-8906

DT400 Battery tester 12V

DT400 Battery tester for 12V batteries WET, GEL, AGM, PbCa. Battery reference standards EN, IEC, DIN, SAE, CA-MCA.

Product code: 802605

STS700 Battery tester 12V

STS700 Battery tester for WET, GEL, MF, AGM, PbCa, EFB batteries from 8-240 Ah at 12V

Product code: 804243

DTP900 Battery tester 12/24V

DTP900 Battery tester 12/24V for WET, GEL, MF, AGM, PbCa, EFB batteries

Product code: 804244

Battery charger Nevada 10 230V

Battery charger Nevada 10 230V for charging free electrolyte batteries (WET)

Product code: 807022

Battery charger / starter Leader 150 Start 230V

Battery charger / starter Leader 150 Start 230V for charging free electrolyte batteries (WET) with 12V voltage.

Product code: 807538

Battery charger Alpine 15 230V 12-24V

Battery charger Alpine 15 230V 12-24V for charging free electrolyte batteries (WET)

Product code: 807544

Battery charger Alpine 20 Boost 230V 50/60Hz 12-24V

Battery charger Alpine 20 Boost 230V 50/60Hz 12-24V for charging free electrolyte batteries (WET)

Product code: 807546

Battery charger / starter Leader 400 Start 230V 12-24V

Battery charger / starter Leader 400 Start 230V 12-24V for charging free electrolyte batteries (WET) with 12/24V voltage.

Product code: 807551

Battery Charger T-Charge 12 6V/12V

T-Charge 6/12V Multifunction, battery charger and maintainer for 6/12V WET, GEL, AGM, MF, PbCa, EFB batteries.

Product code: 807567

Battery charger / starter Alaska 150 Start 230V 12V

Battery charger / starter and maintainer Alaska 150 Start 230V 12V with electronic control of the charging current, automatic interruption and restart.

Product code: 807576

Battery charger Touring 11 230V 6V/12V

Battery charger Touring 11 230V 6V/12V for charging WET, GEL, Pb-Ca, AGM, MF, EFB batteries with 6/12V voltage.

Product code: 807591

Battery Charger T-Charge 20 12V/24V

T-Charge 20 12V/24V Multi-functional electronic battery charger and trickle charger for WET, GEL, AGM, MF, PbCa, EFB, 12V/24V batteries.

Product code: 807594

Battery charger and tricke charger T-Charge 20 Evo 12V/24V

T-Charge 20 Evo 12V/24V Multi-functional electronic battery charger and trickle charger for WET, GEL, AGM, MF, PbCa, EFB, 12V/24V batteries.

Product code: 807596

Battery charger / trickle charger Defender 12 6V/12V

Electronic battery charger and trickle charger Defender 12 6V/12V for WET, GEL, AGM, MF, PbCa, EFB 6V/12V batteries.

Product code: 807607

Battery charger / trickle charger Pulse 30 Evo 230V 12V/24V

Battery charger / trickle charger Pulse 30 Evo 230V 12V/24V for WET, GEL, AGM, MF, PBCA, EFB, Li 12V/24V batteries.

Product code: 807610

Battery charger / starter Doctor Start 530 230V 12V/24V

Battery charger / starter Doctor Start 530 230V 12V/24V for WET, GEL, AGM, MF, PbCa, EFB and Li batteries at 12/24V.

Product code: 829343

Battery charger / starter Energy 650 Start 230-400V 12-24V

Battery charger / starter Energy 650 Start 230-400V 12-24V for charging free electrolyte batteries (WET)

Product code: 829385

Starter Pro Start 2824 12-24V

Starter Pro Start 2824 12-24V. Battery-powered starter suitable for 12-24V starting of cars, vans, boats, agricultural vehicles, power sources etc.

Product code: 829517

Booster Converter 500

Booster Converter 500 12V DC - 230V AC power inverter ideal for power supply by car or camper, of rasors, LCD or plasma TV, halogen wall lamps, hammer drills, polishing machines, electrical tools in general.

Product code: 829446

Starter and tester Startzilla 9012 Xt 12V

Starter Startzilla 9012 Xt 12V Multifunction electronic starter, power supply and tester, with LiFePO4 lithium battery for 12V starting of cars, vans, small boats, lorries etc.

Product code: 829526

Suction cup 1x125mm. Max. capacity: 60kg

An aluminum handle with a suction cup that is designed for carrying elements with a flat and smooth surface, such as windows, car windows, metal sheets, laminates, tiles, etc., their weight cannot exceed 60kg.

Product code: T01250

Digital torque adapter 40-200Nm, 1/2" with 1/4" and 3/8" adapters

Digital torque adapter can be used to recalibrate any type of torque wrench

Product code: T00025

Pneumatic air grinder (straight, 22000rpm)

Pneumatic air grinder is perfect for polishing and cleaning tires, profiles, general high speed grinding and milling of various materials (depending on the attachment used).

Product code: PX82

Pit jack 12 tons with an attachment for transmission lifting

Hydraulic and pneumatic pit jack 12 tons with attachment for gearboxes.

Product code: OSK9.1

Hydraulic and pneumatic pit jack 12t

Hydraulic and pneumatic pit jack 12t. Min and max width: 800mm, 1250mm or custom made.

Product code: OSK8

Pit jack 3.5t

Hydraulic pit jack. Capacity: 3.5tons. Lifting height: 500mm. Min. and max. width: 800-1200mm

Product code: OSK4

Set of 3 stubby ratchets, 1/4", 1/2", 3/8"

3pcs stubby ratchets. 72-teeth ratchets with 1/4", 1/2", 3/8" drive square. Length: 1/4" - 85mm, 1/2" - 135mm, 3/8" - 102mm.

Product code: JBM53671

3 pcs wheel rim protection set

Special tool to reduce the damage of the tires at the time of mounting or disassembling tires

Product code: JBM53419

Removal tool soft grip swivel 500mm

Removal tool soft grip swivel 500mm. Polymer strap (high resistance) 540 x 20 mm. Ø 150mm. Dentated surface for optimal grip.

Product code: JBM52416

Magnetic pick-up tool with led

Magnetic pick-up tool with led. Extensible from 90 to 810mm. Material: steel + magnet. Diameter 15mm. Capacity 1kg.

Product code: JBM51272

Set of 8 short combination spanners

Set of 8 short combination spanners. Measurements: 10, 11, 12, 13, 14, 15, 17, 19mm.

Product code: JBM50564

Buffing stone. Diameter x height: 35x8mm

The 35 x 8mm stone is designed for machining steel cords during tire repair.

Product code: IT208-0291

Rasp wheel. Diameters: 50x10mm

The K18 rasp wheel with a diameter of 50 x 10mm and a thread of 3/8" is designed for roughening the outside of all car, lorry, agricultural and oversized vehicle tires.

Product code: IT205-0143

Tire lever. Lenght: 750mm

This tire changing tool is widened and reinforced, which provides great leverage for tire replacement.

Product code: G71237

Tire lever. Lenght: 600mm

This tire changing tool is widened and reinforced, which provides great leverage for tire replacement.

Product code: G71236

Brush for applying mounting paste to tires and rims

A brush designed to apply the mounting paste to the rim of tires in order to facilitate pulling the tire onto the rim.

Product code: G71216

Precision and standard screwdriver set, 18pcs

Precision and standard screwdriver set on a stand, 18pcs. Phillips, SL, Trox.

Product code: G32003

Screwdriver and bit set, 36pcs

36-piece screwdriver and bit set. Phillips, SL, Torx, PZ bits.

Product code: G32002

Impact spline socket set M14, M16, M18 (length 43mm and 78mm)

Set of impact spline bits used for a variety of applications, particularly VAG wheel hubs and brake calipers

Product code: G10515

Ratchet combination spanner set with flexible head 8-19mm, 6pcs

Ratchet combination spanner set with flexible head 8-19mm, 6pcs. 12-point ratcheting end needs as little as 5 degrees to rotate bolts.

Product code: G10339

Adjustable wrench 0-46mm, 380mm

Adjustable Wrench with a large knurl for easy adjustment and a tight jaw fit. Special hex jaw construction helps reduce slippage and tightly grips the bolt for solid and secure operation.

Product code: G10215

Adjustable wrench 0-19mm, length 150mm

Adjustable wrench with a large knurl for easy adjustment and a tight jaw fit. Special hex jaw design helps to reduce slippage and tightly grips the bolt for solid and secure operation.

Product code: G10206

Torque wrench 1/4", 5-25Nm

Adjustable torque wrench 5-25Nm with 1/4" square drive

Product code: G10063

Telescopic wrench with non-slip handle. Sockets: 17x19mm, 21x23mm

Reinforced, extendable, L type wheel wrench. The telescopic design allows the lever to be extended up to 550mm.

Product code: G10053

Torx, spline, Ribe, hex bit set, 75pcs

A set of bits made of Cr-V steel used to unscrew special screws such as Torx, spline, Ribe and hex.

Product code: G10036

Heat shrink tubes with tin, 100pcs set

The use of tin shrinkable tubing allows for a durable and waterproof connection of two wires, which is possible thanks to the inner layer of glue.

Product code: G03609

Heat shrink tubes with tin, 100pcs set

The use of tin-shrinkable tubing allows for a durable and waterproof connection of two wires, which is possible thanks to the inner layer of glue.

Product code: G03608

Heat shrink tubes with tin, 50pcs set

The use of tin shrinkable tubing allows for a durable and waterproof connection of two wires, which is possible thanks to the inner layer of glue.

Product code: G03607

Air hose extension reel. Lenght: 14m. Input and output hose diameters: 6.5 and 10mm

Pneumatic hose on a reel made of high quality reinforced PVC material. Has high resistance to high pressure. The reel is equipped with automatic block preventing the hose from self-winding all the way up, and a hanger allowing the hose to be hung on the wall.

Product code: G03191

Air hose extension reel. Lenght: 10m. Input and output hose diameters: 8 and 12mm

Pneumatic hose on a reel made of high quality reinforced PVC material. Has high resistance to high pressure. The reel is equipped with automatic block preventing the hose from self-winding all the way up, and a hanger allowing the hose to be hung on the wall.

Product code: G03190

Air ratchet wrench 1/2" 80Nm

Professional air wrench with maximum torque 80 Nm. Ideal for unscrewing all types of joints in hard-to-reach places. It is equipped with direction switch.

Product code: G03155

Magnetic holder for impact wrench and sockets

Magnetic holder for impact wrench and sockets. Powerful magnet on back of the holder body. PVC coated frame.

Product code: G03152

Car electric connectors set, 424pcs

Car electric connectors set, 424pcs. For replacing ignition switches and many more.

Product code: G02929

Car panel and upholstery push-in rivet set, 456pcs

Car panel and upholstery push-in rivet set, 456pcs

Product code: G02928

Copper washer set, 580pcs (metric)

Copper washer set, 580pcs (metric)

Product code: G02916

E-Clip stainless steel external retaining ring set, 300pcs

E-Clip stainless steel external retaining ring set, 300pcs. Set includes 300pcs of 9 most used sizes: 1.5, 3, 5, 6, 10, 12, 15, 19, 22mm.

Product code: G02914

Car non-insulated terminal connector set, 600pcs

Car non-insulated terminal connector set, 600pcs. For many applications such as car alarms, headlight, remote start, relay,stereos etc.

Product code: G02829

Car mini bladed fuse set, 140pcs

Car mini bladed fuse set, 140pcs

Product code: G02825

Glass fuse set, 120pcs

Glass fuse set, 120pcs. 5-30A capacity.

Product code: G02816

Metric copper washer set, 300pcs

Metric copper washer set, 300pcs. Copper washers are corrosion resistant in wet environments, nonmagnetic, and electrically conductive.

Product code: G02811

Car fuse set 5A-30A, 120pcs

Car fuse set 5A-30A, 120pcs.

Product code: G02809

5pcs strut nut tool set for Audi, VW and Mercedes

A set of nut tools for tightening and loosening shock absorber mounts.

Product code: G02785

Alternator clutch key with socket stem

A key dedicated to alternators with a clutch, enabling unscrewing the bolt securing the pulley for easy removal of the V-belt.

Product code: G02783

Alternator key with 6 point 17mm outter drive. Length 30mm

Bosch alternator clutch wrench. A specialist wrench for assembly and disassembly of the pulley clutch of Bosch alternators.

Product code: G02782

Wiper arm puller

Wiper arm puller. The puller is used to remove car wiper arms. Made of durable chrome-molybdenum steel.

Product code: G02770

Adapter set for gearbox fluid change (ATF)

Adapter set for gearbox fluid change (ATF).

Product code: G02733

Tube double flaring tool set, 10pcs

Tube double flaring tool set, 10pcs, tube sizes: 3/16", 1/4", 5/6", 3/8", 7/6", 1/2", 5/8"

Product code: G02721

Tube flaring set 3-19mm

Tube flaring set for tubes with diameters: 3, 5, 6, 8, 10, 12, 15, 16, 18, 19mm.

Product code: G02720

Hook and pick set 6pcs (Lenght: 240mm)

Hook and pick set for removing seals, O-rings and gaskets.

Product code: G02706

Plastic scraper set for adhesive weights. 4pcs 18-36mm

Set of plastic scrapers for removing adhesives weights. 4 different widths 18, 20, 25 and 36mm.

Product code: G02592

Ball joint seperator for pin diameters up to 19mm

Professional ball joint pin puller. It is made of durable, high-quality tool steel. It is adapted to work with pins with a diameter of not more than 19mm.

Product code: G02587

3pcs Ball joint remover set. Diameters: 23, 28, 34mm

Pullers for ball joints on stabilizers and torsion bars. Suitable for cars and vans.

Product code: G02585

Universal ball joint puller for pins up to 20mm in diameter.

Universal ball joint puller with lever. Made of forged steel. Its compact size allows you to work in hard to reach areas.

Product code: G02583

Internal bearing extractor set. Diameters: 8-58mm

Precision puller for tight-fitting, internal bearings and bushings.

Product code: G02577

Oil filter strap wrench 85-95mm

Band wrench for replacing oil filters in cars and vans. Designed for filters with a diameter of 85 to 95mm.

Product code: G02562

Chain type oil filter wrench

Chain type oil filter wrench. Widely used for pipeline construction and oil filter removal.

Product code: G02555

Foldable undercar creeper and workshop seat

Foldable undercar creeper and workshop seat. Quick and simple conversion from creeper into a stool.

Product code: G02098

Double chain type universal oil filter wrench

Suitable for oil filters up to approximately 130mm (5,1/4") in diameter.

Product code: G02554

Universal three arms oil filter wrench 3/8" (65-130mm)

Oil filter wrench with 3 arms can be adjusted from 65 - 130mm in diameter. Comes with an adapter so it fits any 3/8" and 1/2" square drive ratchets or extensions.

Product code: G02550

Inner tie rod remover and installer tool. For rod diameters: 35-41mm

Track Rod End Remover & Installer 35-41mm

Product code: G02548

Inner tie rod remover and installer tool. For rod diameters: 28-35 mm

Inner tie rod remover and installer tool. For rod diameters: 28-35 mm

Product code: G02547

Brake piston presser. Max 70mm jaw spread.

Essential tool for pressing in the brake piston to allow insertion of new brake pads.

Product code: G02534

Compression pressure test set for diesel engines

With the help of the gauge you can measure the pressure in each cylinder. It allows you to quickly identify damaged fuel pumps. Max. pressure 70bars (1000psi).

Product code: G02515

Compression pressure test set for diesel engines

The set allows for quick identification of damages to the cylinders and injectors.

Product code: G02510

Suction cup. Diameters: 2x115mm

The suction cup designed to carry elements with a flat and smooth surface, such as windows, car windshields, metal sheets, laminates, tiles, etc.

Product code: G02454

Triple suction cup. Diameters: 3x115mm

The suction cup designed to carry elements with a flat and smooth surface, such as windows, car windshields, metal sheets, laminates, tiles, etc.

Product code: G02452

Double suction cup. Diameter: 2x115mm

The suction cup designed to carry elements with a flat and smooth surface, such as windows, car windshields, metal sheets, laminates, tiles, etc.

Product code: G02451

Suction cup. Diameter: 1x115mm

The suction cup designed to carry elements with a flat and smooth surface, such as windows, car windshields, metal sheets, laminates, tiles, etc.

Product code: G02450

A pair of battery cable clamps

Universal battery cable clamps. 2pcs Both positive and negative (marked on the terminal). The clamps are suitable for 6V or 12V batteries.

Product code: G02400

Gear and bearing puller with 3 jaws. Max capacity: 14" (350mm)

Gear puller with 3 jaws 14" (350mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02247

Bearing and gear puller with 3 jaws. Working range: up to 10" (254mm)

Bearing and gear puller with 3 jaws. Working range: up to 10" (254mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02245

Bearing and gear puller with 3 jaws. Working range: up to 8" (203mm)

Bearing and gear puller with 3 jaws. Working range: up to 8" (203mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02233

Bearing and gear puller with 3 jaws. Working range: up to 6" (152mm)

Bearing and gear puller with 3 jaws. Working range: up to 6" (152mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02232

Two jaw gear and bearing puller. Operating range: up to 200mm

Two jaw gear and bearing puller with adjustable clamping depth and width. For both internal and external bearings.

Product code: G02202

Motorcycle lift and stand, 340kg

Motorcycle lift and stand, 340kg

Product code: G02172

Motorcycle lift and stand for Cross and Enduro bikes

Motorcycle lift and stand for Cross and Enduro bikes.

Product code: G02168

Motorcycle lift and stand, flat pads (rear), 500kg

Motorcycle lift and stand, flat pads (rear), 500kg

Product code: G02166

Hydraulic hand pump 10t

Hydraulic hand pump with quick coupler, 10t

Product code: G02071

Timing tool RENAULT,NISSAN,OPEL 1.6, 2.0 C01/0199

Product code: C01/0199

Balance shaft lock for BMW N20 / N26 + oil pump tool C01/0203

Product code: C01/0203

Engine Timing Tool Set 1.5, 1.9, 2.2, 2.5 DCi Renault, Opel, Nissan С01/0215

Product code: C01/0215

BMW and Mini timing lock N13, N18 1.6 pre-tensioning tool set

Timing lock set for BMW and Mini petrol engines N13,N18 timing chains.

Product code: C01/0222

Timing lock for Citroen, Peugeot, Opel 1.2 Vti (VVT), GDI

This tool kit makes it easy to change the timing belt without having to disassemble multiple components. Allows you to determine if the belt needs to be replaced without having to disassemble the engine.

Product code: C01/0230

Engine Timing Tool Set - for BMW 2.0 and 3.0 N47 / N47S / N57 Common Rail C01/0233

Product code: C01/0233

Engine timing tool set for Opel 1.6 CDTI Ecoflex

Engine timing tool set for Opel 1.6 CDTI Ecoflex

Product code: C01/0237

Timing tool set for Jaguar, Land Rover Evoque 2.0T

Timing tool set for Jaguar F-Pace, XE, XF (2015 onwards), Land Rover Discovery Sport, Range Rover Evoque (2015 onwards)

Product code: C01/0238

Stud Wrench 8" 12-21mm

Fully adjustable with a one-handed squeeze. Efficient ratcheting by releasing, then re-gripping the object. Often removes nuts and bolts damaged by other tools.

Product code: G00860

Hydraulic jaw puller kit 5t

Multi-function puller with adjustable two or three leg function. Allows bearings, gears, etc. to be easily removed with minimal effort by use of the hydraulic puller.

Product code: G00910

Hydraulic jaw puller set 10t

Multi-function puller with adjustable two or three leg function. Allows bearings, gears, etc. to be easily removed with minimal effort by use of the hydraulic puller.

Product code: G00911

Manual fuel transfer and priming pump

Hand pump for pumping and bleeding diesel fuel systems when replacing the fuel filter and other work related to the fuel system.

Product code: G00985

Grease gun. Capacity: 500ml

The manual grease gun is used for the precise distribution of solid lubricants on surfaces and mechanical elements such as bearings, joints, pins, shafts, etc.

Product code: G01121

Cleaning air gun with reservoir 1L

The cleaning air gun is a great tool for removing dust and stains from hard-to-reach areas such as seat runners, door trims, dashboards, upholstery and even bodywork.

Product code: G01158

3pcs air blow gun set. Nozzle lenghts: 100, 300 and 500mm

3pcs air blow gun set. Nozzle lenghts: 100, 300 and 500mm

Product code: G01164

CV joint clamp banding tool

CV joint clamp banding tool is suitable for installation and tightening of band-style clamps on CV joint boots, power steering rack and pinion steering gear boots.

Product code: G01653

Circlip pliers set 7" (180mm)

Circlip pliers set 7" (180mm) includes pliers with straight tips and angled tips for internal and external circlips.

Product code: G01661

Long ball end hex key set 9pcs, 1.5-10mm, 260mm

Long ball end hex key set 1.5-10mm. Set includes 9 pieces of long hex keys: 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10mm.

Product code: G01703

Long ball end hex key set 9pcs, 1.5-10mm

Ball end long hex key set 1.5-10mm. Set includes 9 pieces of long hex keys: 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10mm.

Product code: G01704

Long Torx key set T10-T40 7pcs

Long Torx key wrench set T10-T40. Set includes 7 pieces of long Torx key wrenches: T10, T15, T20, T25, T27, T30, T40.

Product code: G01706

Fender reforming and extending tool

A fender roller that can be used to increase the clearance between the tire and the fender to fit larger tires or repair the dents or damages on the fender.

Product code: G02049

Pneumatic air jack triple balloon type. Capacity: 3T

Pneumatic air jack triple balloon type. Capacity: 3T. Maximum lifting height: 400mm. Airbag diameter: 120mm.

Product code: G02062

Manual oil pump 1.5L

Manual suction device with a capacity of 1.5l. The device is designed to suck out or dispense oil and other operating fluids in hard-to-reach places.

Product code: G02124

Oil funnel with built in filter

Oil funnel with built in filter and flexible hose. Dia.: 140mm

Product code: G02150

Motorcycle stands front and rear set

Motorcycle stands combo set. Two stands and three pairs of different arms (fork, spool and square cradles).

Product code: G02167

Motorcycle scissor lift, 500kg

Motorcycle scissor lift, 500kg

Product code: G02170

Motorcycle and ATV jack, 680kg, 115-375mm

Hydraulic jack for lifting motorcycles and ATVs, lifting capacity 680kg

Product code: G02180

Engine hoist load balancer 908kg

Easily lifts and balances engines or other suspended loads with offset center of gravity.

Product code: G02192

Two jaw gear and bearing puller. Operating range: up to 100mm

Two jaw gear and bearing puller with adjustable clamping depth and width.

Product code: G02200

Two jaw gear and bearing puller. Operating range: up to 150mm

Two jaw gear puller with adjustable clamping depth and width.

Product code: G02201

Bar type gear and bearing pullers with two jaws. Working range: 250mm

Two jaw gear puller with adjustable clamping depth and width. For both internal and external bearings.

Product code: G02203

Bearing and gear puller with 3 jaws. Working range: up to 12" (305mm)

Bearing and gear puller with 3 jaws. Working range: up to 12" (305mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02235

Portable air sand blaster. Capacity: 10L

The set includes a professional sand blasting gun with a set of 4 ceramic nozzles (4, 5, 6, 7 mm) and a 4.5m long hose.

Product code: G02270

Vacuum gauge and fuel pump pressure tester set with adapters

Measures vacuum up to 70cmHg and pressure up to 0.7bar. Fittings included for compatibility with most cars.

Product code: G02508

Multi functional cylinder pressure gauge

Multi functional cylinder pressure gauge with clear LCD display. Measures the pressure in the combustion chamber of the petrol engine.

Product code: G02509

Oil filter strap wrench 95-110mm

Band wrench for replacing oil filters in cars and vans. It is designed for automotive repair.

Product code: G02563

Oil filter strap wrench 60-105mm

Band wrench for dismounting all types of oil filters with a diameter of 60 to 105mm.

Product code: G02564

Lever style valve spring extractor. For 8, 16, 24V engines

Lever press designed to disassemble and remove valve springs in 8V/12V/16V/24V OHV, OHC and CVH engines. Adapters: 24, 30, 35mm

Product code: G02573

Multifunctional set of prying tools for upholstery clips and stereo. 20pcs.

This set of prying tools allows you to remove upholstery clips quickly. They do not have sharp edges - so there is no risk of scratching the upholstery.

Product code: G02578

Oil drain pan 10L

A container ideal for the recovery of oil and antifreeze liquids.

Product code: G02634

Mini set for dent repair. 7pcs

A repair kit designed to remove small dents in the car body. 100% safe for car paint thanks to it's rubber padded feets. The set includes 7 mushrooms of different diameters and sizes.

Product code: G02645

Motorcycle front axle hex socket, 17, 19, 22, 24mm

3/8" Motorcycle hex axle socket is designed for easy installation, removal, or adjustment of front wheel axles on sport and dirt bikes with hexagonal axle holes.

Product code: G02685

Windshield sealant cutting tool

Removes the urethane sealing material around the windscreens after removing the rubber.

Product code: G02701

Hook and pick set, 9pcs

Hook and pick set for removing oil seals, o-rings and gaskets

Product code: G02708

Tube flaring tool set with pipe cutter

Tube flaring tool set with pipe cutter. For tube sizes: 5, 6, 8, 10, 12, 14, 18mm.

Product code: G02722

Tube bending tool. For diameters: 6-10mm

Designed for bending copper tubes, aluminium tubes and stainless steel tubes.

Product code: G02723

Car exhaust pipe cutter. 18-93mm

Chain type pipe cutter, ideal for cutting exhaust pipes. Also can be applied on thin walled copper or steel tubes. Cutting capacity up to 93mm diameter.

Product code: G02726

Brake system bleeding set

Pneumatic brake system bleeding set.

Product code: G02732

Inner bearing puller set. For diameters: 10-32mm

The internal bearing puller designed for dismounting internal bearings with an internal diameter of 10-32mm.

Product code: G02747

Clutch aligning tool with 3 sleeves

A high-quality universal tool for locking the clutch disc, ideal for manual alignment (centering) and applying the clutch disc to the pressure plate in cars and vans.

Product code: G02766

O-ring set, 419pcs

O-rings resistant to acid, petrol, oil, and high temperature.

Product code: G02800

O-ring set, 900pcs

O-ring set, 900pcs.

Product code: G02801

External circlip set 300pcs (Dimeters: 3-32mm)

External circlip set 300pcs (Dimeters: 3-32mm)

Product code: G02802

Metric copper washer set, 150pcs

Metric copper washer set, 150pcs

Product code: G02807

O-ring set for car air conditioning system, 420pcs

O-ring set for car air conditioning system, 420pcs with 18 different sizes. (Diameters: 5.29 - 17.17mm)

Product code: G02818

Heat shrink tubing set, black, 100pcs

This kit contains 100 pieces of assorted heat-shrink tubing in a range of diameters.

Product code: G02822

Car non-insulated terminal connector set, 750pcs

Car non-insulated terminal connector set, 750pcs

Product code: G02828

Thread repair set, M5x0.8

Thread repair set, M5x0.8 with 30 spiral inserts.

Product code: G02880

Thread repair set, M6x1.0

Thread repair set, M6x1.0 with 30 spiral inserts.

Product code: G02881

Straight die grinder air tool 1/4" with a set of accessories

The air die grinder is a great tool for sanding, grinding, deburring and engraving in a variety of different materials.

Product code: G03143

Oil gun 250ml

Oil gun with a capacity of 250ml. Designed for pumping oil or other lubricants into hard-to-reach places, such as drive axles, gearboxes, etc.

Product code: G03220

Oil gun 250ml - clear tank

Professional oiler with a capacity of 250ml. Designed for pumping oil or other lubricants into hard-to-reach places, such as drive axles, gearboxes, etc.

Product code: G03221

Steel bearing balls set, 470pcs

Steel bearing balls set, 470pcs, 11 different sizes. Made of high-quality steel.

Product code: G03605

Cross wrench. Dia. 14". Sizes: 17x19x21x1/2" with reinforced type black dipper handle

Cross wrench. Dia. 14". Sizes: 17x19x21x1/2" with reinforced type black dipper handle.

Product code: G10054

Torque wrench 3/8", 19-110Nm

The torque wrench is made of thick steel. The reinforced ratchet has two supports on the rack, which results in increased durability of the wrench mechanism by distributing the force.

Product code: G10059

Ratchet combination spanner set with flexible head 8-22mm, 8pcs

Ratchet combination spanner set with flexible head 8-22mm, 8pcs. 12-point ratcheting end needs as little as 5 degrees to rotate bolts.

Product code: G10338

Ratchet combination spanner set 6-32mm, 22pcs (in aluminum case)

Ratchet combination spanner set 6-32mm, 22pcs. 12-point ratcheting end needs as little as 5 degrees to rotate bolts.

Product code: G10341

6 points socket set for alloy rims. Sizes: 17, 19, 21mm

The plastic sleeve protects surfaces next to the heads of screws and nuts.

Product code: G10510

Rolling workshop seat with tool tray

Features a soft, fully padded seat for added cushioning, making it comfortable to work on your car, truck, SUV, van, and more. Equipped with four 360-degree swivel casters which deliver smooth and precise movements.

Product code: G10825

Mechanics rolling knee pads 100kg

Rolling knee pads allow you to be mobile and easily move from side to side while protecting your knees. Built in tray and holder to keep your small tools and parts handy.

Product code: G10827

Torx/E-ring spanner set E6-E24, 4pcs

Set includes four Torx/E-ring spanners: E6xE8, E10xE12, E14xE18, E22xE24

Product code: G11149

6pcs bit adapter set with square drives

Bit adapter set in 6 different sizes. Made of chromium vanadium steel. Fitted with locking balls.

Product code: G13543

Valve stem puller

This device allows you to easily pull the valve through the holes on steel or aluminum rims without much effort.

Product code: G71205

Car wheel chocks 2pcs

They are designed to protect various types of vehicles against accidental movement by placing them under the wheels.

Product code: G71211

Magnetic mat for screws. Dimensions: 25x20cm

It has a magnetic attraction, which can attract more small screws and micro metal parts and fix them in place.

Product code: G73306

Air inflator with digital gauge

Digital Pressure Gauge, Scale:0-200Psi, 0-14Bar, 0-1400Kpa, 0-14Kgf/cm², 300mm kink resistant hose, Large numerical display with user selectable pressure units

Product code: JBM53450

Pit jack 3.5t. Lowered

Pit jack 3.5 tons - Low. Lifting height: 500mm. Width 800 - 1200mm

Product code: OSK2

Hydraulic and pneumatic pit jack 7t

Hydraulic and pneumatic pit jack 7t with custom made width.

Product code: OSK6

Portable induction heater 1500W

Mobile induction heater for fast heat delivery.Install appropriate coil and place over or aroud ferrous metal.Ideal for loosening stubborn and seized fixings.

Product code: MH1500

Cutter for tire repair 10mm

Cutters are designed for cleaning and enlarging holes on punctured radial and diagonal tires.

Product code: 511-1310

Cutter for tire repair. Diameter 12mm

Cutters are designed for cleaning and enlarging holes on punctured radial and diagonal tires.

Product code: 511-1320

Cutter for tire repair. Diameter 3mm

It is designed for cleaning and enlarging holes on punctured radial and diagonal tires.

Product code: 511-1330

Cutter for tire repair. Diameter 6mm

It is designed for cleaning and enlarging holes on punctured radial and diagonal tires.

Product code: 511-1360

Tool holder (shank), for tools with 6mm shank

Tool holder (shank), for tools with 6mm shank

Product code: 519-6672

Buffing ball 40x6mm - pumice stone

The pumice stone is designed for machining steel cords on the inside of car and lorry tires. Ball diameter: 40mm, shank diameter: 6mm.

Product code: 595-0083

Buffing stone, 20x65mm

The 20 x 65mm stone is suitable for machining steel cords during repairs.

Product code: 595-0629

Buffing ball. Diameter: 20mm

The 20mm stone is suitable for machining steel cords during tire repair.

Product code: 595-0681

Wire brush. Diameter: 55mm

The 55 x 8mm brass brush is designed for roughening rubber on the outside and inside of all types of tires.

Product code: 595-0722

Rasp cone. Diameters: 27x102mm

The K18 rasp cone with a diameter of 25 x 102mm and a thread of 3/8" is designed for the roughening of the outside of lorry, agricultural and oversized vehicle tyres.

Product code: 595-0739

Pressure roller for tire repair. Width: 12mm

The 12mm wide bearing roller with a diameter of 35mm combined with a wooden handle makes up a pressure roller.

Product code: 595-1123

Tire scraper

The flat and curved surface scraper enables pre-cleaning of the inside and outside of the tire.

Product code: 595-1178

PVC coated steel wire buffer. Diameter: 76mm, height: 8mm

The PVC coated steel wire buffer with a diameter of 76 x 8mm is designed for roughening the rubber on the outside of car, van and agricultural vehicle tires.

Product code: 595-4168

K18 rasp wheel. Dimater and height: 76x32mm

The K18 rasp wheel with a diameter of 76mm and 14mm hole is designed for roughening the inside of lorry, agricultural and oversized vehicle tires.

Product code: 595-4223

Buffing wheel. Diameter: 65mm

The K170 buffing wheel with a diameter of 65mm and a 3/8" thread is designed for roughening the inside of lorry, agricultural and oversized tires.

Product code: 595-4357

Rasp ball. Diameter: 20mm

The K330 rasp ball with a diameter of 20mm is designed for roughening the outside of rubber tires, mainly of cars and lorries.

Product code: 595-4371

Whetstones for rotary gouge

The whetstone is used to sharpen rotary gouges of all sizes.

Product code: 595-4481

Rasp wheel. Diameter: 50mm

The K18 rasp wheel with a diameter of 50mm and a thread of 3/8" is designed for roughening the outside of lorry, agricultural and oversized vehicle tires.

Product code: 595-4388

Cylinder wire brush. Tip diameter: 8mm

The steel brush with a diameters of 8 x 25mm is designed for roughening the rubber on the outside of all types of tires.

Product code: 595-4560

K170 buffing wheel. Diameters: 44x19mm

The K170 buffing wheel with a diameter of 44mm and a 3/8" thread is designed for roughening the inside of passenger car tires.

Product code: 595-4632

Tire repair rasp kit

The set consists of a cone, ring, pencil and a ball rasp.

Product code: 595-4711

K170 rasp dome. Diameters: 32x18mm

The K170 rasp dome with a diameter of 32mm and a 3/8" thread is designed for roughening the inside of car tires.

Product code: 595-4735

Buffing stone. Diameters: 50x10mm

The 50 x 10mm stone is designed for machining steel cords during tire repair.

Product code: 595-4797

Buffing stone. Diameters: 14x45mm

The 14 x 45mm stone is designed for machining steel cords during tire repair.

Product code: 595-4810

Cutter for tire repair. Diameter x Lenght: 6x90mm

Durable cutter designed to expand the hole on the damaged tire usable during repairs with inserts or pins.

Product code: 595-4962

Cutter. Diameter x length: 8x100mm

Durable cutter designed to expand the hole on the damaged tire usable during repairs with inserts or pins.

Product code: 595-4948

Cutter for tire repair. Diameter x lenght: 12mm x 110mm

Durable cutter designed to expand the hole on the damaged tire usable during repairs with inserts or pins.

Product code: 595-5040

Drum sander for tires 6pcs. Diameter x height: 45mm x 30mm

The buffing tool with a diameter of 45mm is designed for the removal of outflows caused by thermopresses.

Product code: 595-5507

Rasp dome. Diameters: 50x25mm - 16mm

The K18 rasp dome with a diameter of 50mm and a 3/8" thread is designed for roughening the inside and outside of lorry, agricultural and oversized vehicle tires.

Product code: 595-6056

Rasp cone. Diameters: 25x50mm

The K18 rasp cone with a diameter of 25 x 50mm and a thread of 3/8" is designed for the roughening of the outside of lorry, agricultural and oversized vehicle tires.

Product code: 595-8872

Pressure roller with wooden handle

It is mainly designed for pressing patches during tire or inner tube repairs.

Product code: 596-1027

STS600 Battery tester 12V

STS600 Battery tester for WET, GEL, MF, AGM, PbCa, EFB batteries.

Product code: 804242

DTP790 Battery tester 12V

DTP790 Battery tester 12V for WET, GEL, MF, AGM, PbCa, EFB batteries

Product code: 804245

Battery charger Nevada 15 230V

Battery charger Nevada 15 230V for charging free electrolyte batteries (WET)

Product code: 807026

Battery charger Computer 48/2 Prof 230V 6-48V

Battery charger Computer 48/2 Prof 230V 6-48V for charging all types of batteries (WET) with 6/12/24/36/48V voltage

Product code: 807063

Battery charger Autotronic 25 Boost 230V 12V/24V

Battery charger Autotronic 25 Boost 230V 12V/24V with automatic interruption and restart (TRONIC)

Product code: 807540

Battery charger Defender 8 6V/12V

Intelligent battery charger and maintainer Defender 8 6V/12V with electronic control of the charging current.

Product code: 807558

Battery charger Touring 15 230V 12V/24V

Battery charger Touring 15 230V 12V/24V for charging WET, GEL, Pb-Ca, AGM, MF, EFB batteries with 12/24V voltage.

Product code: 807592

Battery charger / trickle charger T-Charge 26 Evo 12V/24V

Battery charger / trickle charger T-Charge 26 Evo 12V/24V for WET, GEL, AGM, MF, PbCa, EFB, Li 12V/24V batteries.

Product code: 807595

Battery Charger / trickle charger Pulse 50 Evo 230V 12V/24V

Battery Charger/ trickle charger Pulse 50 Evo 230V 12V/24V for WET, GEL, AGM, MF, PbCa, EFB, Li 12V/24V batteries.

Product code: 807611

Battery charger and manager Doctor Charge 55 Connect 230V 6V/12V/24V

Battery charger and manager Doctor Charge 55 Connect 230V for complete maintenance of WET, GEL, AGM, MF, PbCa, EFB, Li 6V/12V/24V batteries.

Product code: 807614

Battery charger / starter Energy 1000 Start 230-400V

Battery charger / starter Energy 1000 Start 230-400V for charging free electrolyte batteries (WET)

Product code: 829008

Battery charger / starter Energy 1500 Start 230-400

Battery charger / starter Energy 1500 Start 230-400 for charging free electrolyte batteries (WET)

Product code: 829009

Booster Converter 310 Usb

Booster Converter 310 Usb. 12 VDC - 230 VAC power inverter ideal for power supply by car or camper, of rasors, LCD or plasma TV, halogen wall lamps, hammer drills, polishing machines, electrical tools in general.

Product code: 829444

Booster Converter 1000

Booster Converter 1000 12V DC - 230V AC power inverter ideal for power supply by car or camper, of rasors, LCD or plasma TV, halogen wall lamps, hammer drills, polishing machines, electrical tools in general.

Product code: 829447

Starter and tester Startzilla 4012 Xt 12V

Starter Startzilla 4012 Xt 12V Multifunction electronic starter, power supply and tester, with LiFePO4 lithium battery for 12V starting of cars, vans, small boats, lorries etc.

Product code: 829527

Starter Drive Pro 12V/24V

Starter Drive Pro 12V/24V with two USB outputs (1A-2,1A) to charge (power bank) electronic devices (tablets, smartphones, etc.)

Product code: 829573

Air conditioning compressor clutch removal set

A/C compressor clutch removal set for cars (GM, Ford, Chrysler).

Product code: CKB04040

Universal pulley fan clutch holder

Designed to remove and install fan clutch and rotate or restrain the camshaft pulley. Adjustable jaw spread and interchangeable pins.

Product code: CKB04049

Brake piston driver

Device for screwing the brake pistons.

Product code: CKB04078

Piston ring compressor pliers

Piston ring compressor pliers. Operating range: 110-160mm.

Product code: CKB04082

Engine cylinder honing tool 45-88mm

Has 3 grinding stones and a spring to grant smooth operation. For sleeves with diameters of 45-88mm. Attachable to drills.

Product code: CKB04137

Cylinder honing tool. For diameters: 51-177mm

Cylinder honing tool. For diameters: 51-177mm

Product code: CKB04138

Ignition timing lamp

A strobe lamp for setting the ignition angle is used to check and adjust the ignition timing of gasoline engines. 

Product code: CKB04795

Hole punching and bending hand tool

Professional hand tool used for punching holes or bends along the edge of the sheet allowing you to connect two elements together. 

Product code: CKB07004

Injector testing tool with adapters ( Capacity: 600bar)

The injector tester is used to regulate and check the pressure, the leaks and the quality of the spraying of the injector, to ensure excellent power and economical operation of the engine.

Product code: CKB08039

AC and fuel line disconnect set

Set for disconnecting fuel and air-conditioning quick connectors. 

Product code: CKB09042

Flaring tool kit for brake lines

For making ends of brake lines or copper, copper-nickel and thin-walled steel pipes. Adapters: 4.75, 6.35, 7.95, 9.50, 11.10, 12.70, 15.87mm

Product code: CKB09065

Universal valve spring compressor kit

Universal valve spring compressor kit. Designed to enable the replacement of valve springs and valve stem oil seals. Diameters: 34mm, 26mm, 20mm.

Product code: CKBA2308

Car stethoscope

The car stethoscope is used for auscultation diagnosis. Eliminates sounds from other points than auscultated. 

Product code: CHS-A1022

Windshield sealant cutting tool

Removes the urethane sealing material around the windscreens after removing the rubber.

Product code: CKB00793

Engine timing tool kit for BMW S54 engines

Specifically designed for the popular BMW M3 fitted with the chain driven 3.2 litre 6 cylinder 24-valve petrol engines. Engine code S54 (32 6S 4)

Product code: CKB01062

Carburettor testing kit

A kit for testing the fuel pump carburettor and automatic gearboxes is used for synchronization of car and motorcycle carburettors, 2T and 4T. 

Product code: CKB0112

Cam belt tension gauge

The timing belt tension indicator can be used to adjust the timing belt movement in ranges of 1daN to 10daN. 

Product code: CKB01597

Timing belt tensioner wrench for VW, Audi

Timing belt tensioner wrench for VW, Audi

Product code: CKB01629

Pneumatic ATF fluid extractor / dispenser 10l

Pneumatic fluid changer for replacing oil in automatic gearboxes and differential gearboxes. The set includes 13 adapters for a wide range of automatic gearboxes (VAG, BMW, Ford and Mercedes-Benz)

Product code: CKB03689

Internal bearing puller set

Internal bearing puller 10-32 mm. A professional set, necessary in every workshop.

Product code: CKB04004

Ball joint separator and installer tool set

This ball joint tool kit is suitable for removing and fitting press-fit type ball joints without removing the vehicle's control arm. The pressing device's gap size is 152mm.

Product code: CKB04011

Break piston removal tool

Essential tool for retracting the brake piston to allow insertion of new brake pads.

Product code: CKB04066

Oil cap socket set with ratchet and wrench

A set for unscrewing oil filter caps.

Product code: CKB04111

O-ring and oil seal removal tool

Universal double hook puller for removing O-rings and oil seals.

Product code: CKB04117

7pcs air conditioning and fuel line disconnect set

A practical set of 7pcs of quick disconnect tools for AC and fuel lines.

Product code: CKB09041

Adjustable timing pulley remover 42 - 82mm

Adjustable timing pulley remover 42 - 82mm

Product code: CKBA2213

Piston ring groove cleaning tool set 4pcs

For the removal of carbon deposits from piston ring grooves. Three six sided wheel cutters cover all standard size piston grooves.

Product code: CKBA1040

Overhead valve spring removal tool

Allows valve springs and valve stem oil seals to be replaced in the cylinder head. For OHV, OHC and CHV engines.

Product code: CKBA2114

Valve lapping tool set. Attachable to drills.

This tool smoothens the surfaces of new valves, ensuring that they fit firmly into the cylinders. With 4 different suction cups with 20, 30, 35, 45mm diameters.

Product code: CKBA2269

Cylinder leak-down tester

A classic device for checking the tightness of cylinders with compressed air in a compact design. Adapters: M14x1.25 (short), M18x1.5, M14x1.25 (long).

Product code: CHS-A0021

Universal fuel injector test set 41pcs

The gauges are designed to measure fuel pressure in both low and high pressure systems. The kit includes two gauges, adapters and hoses.

Product code: CHS-A0125

Fuel injector pressure tester kit

Fuel injector pressure tester for petrol engines.

Product code: CHS-A1011

Hand held vacuum pump

Accepts many kinds of adapters to fit most types of vehicles. The body has a switch to control two kinds of pressure conditions. Pressure ranges: positive pressure 0-60psi (1-4inhg) and negative pressure 0-30psi (0 to -1inhg).

Product code: CHS-A998A

Oil drain socket set 12 pcs

Oil drain hex and square sockets set. Square: 8, 11, 13 mm. Hex: 8, 9, 10, 12, 14, 17 mm.

Product code: CHS-E1156

Oil pan thread repair set for M14x1.5 pans

Oil pan thread repair set for M14x1.5 pans

Product code: CKB0025-3

Ball joint press set

For the removal of ball joints, U-joints, brake anchor pins, and more on most 2 wheel drive (2WD) and 4 wheel drive (4WD) vehicles without removing the control arm from the vehicle.

Product code: CKB04009

Valve spring compressor and valve stem seal remover set

For dismantling valves in OHV and OHC engines, without dismantling the cylinder head. 5, 6, 7, 9, 10, 11.5 mm adapters included.

Product code: CKB04023B

Coil spring compressor kit

Coil spring compressor kit for passenger cars and vans. Max working lenght: 300mm. Max. pressure: 2.651kg.

Product code: CKB04027B

Pulley holding double pin wrench set for VW, Audi 1.9 TDI PD, 1.4 TDI engines

Pulley holding double pin wrench set for VW, Audi 1.9 TDI PD, 1.4 TDI engines. 3pcs.

Product code: CKB01886

A set of plastic prying tools 4 pcs

A set of plastic prying tools 4 pcs. Smart alternative of metal prying tools.

Product code: CKB04216

Timing lock set VAG 1.2, 1.4, 1.6 FSI, 1.4 TSI

Timing lock VAG 1.2, 1.4, 1.6 FSI, 1.4 TSI. Set for checking and regulating the crankshaft.

Product code: CKB08060A

Stand for mounting engines. Capacity: 450kg.

A workshop helper for working with the engine. It has four movable grippers fastened to a plate that rotates in 360°. 

Product code: CT63002C

Ball joint removal tool set

Designed for easy removal of most popular types of pitman arms, tie rods and ball joints. Operation range: 17, 19, 21, 23, 27mm

Product code: CKB04340

Universal clutch and clutch drive plate aligning kit

Clutch alingment tool set 16 adapters, 1 shaft.

Product code: CKB04227

Valve lapper set

A reliable set of two valve lappers for engine valves. The ends have rubber suction cups. Diameters: 16, 20.5, 28.5, 30mm

Product code: CKB04220

Set of lambda probe oxygen sensor, vacuum switch remover

Professional set of lambda probe caps 7 pcs. 1/2", 3/8" x 22, 27, 29 mm. Suitable for removing and installing oxygen sensors, oil pressure switches, oil pressure sending units, thermal sensor switches, vacuum switches and break light switches.

Product code: CKB04042

Diesel fuel injection pump timing set

Tool for setting diesel injection pump's timing. For Bosch, Lukas, CAV. For cars: Fiat, Lancia, Alfa Romeo, VW, Audi, BMW, Ford, Renault, Rover, Iveco, Mitsubishi, Isuzu and others.

Product code: CKB01610

Quick disconnect tool kit for A/C, fuel line and transmission oil cooler line 21pcs

Quick disconnect tool kit for A/C, fuel line and transmission oil cooler line 21pcs. Suitable for Ford, Vauxhall, Opel amongst others

Product code: CKBD1005

Bush, bearing and seal driver set 52pcs

Bush, bearing and seal driver set 52pcs. Discs: 18 - 65mm and 74mm

Product code: CKBB1035

Chain cutter for steel and copper tubes

Self-locking chain mostly for cutting exhaust pipes. Featuring 14 cutting blades.

Product code: CKB04775

Pilot bearing puller. For bearing with inner diameters: 12-38mm

Suitable for removing tight fitted sleeve type bearings and bushings with inner ring diameters of 12 to 38mm.

Product code: G30301

Tire lever. Lenght: 400mm

This tire changing tool is widened and reinforced, which provides great leverage for tire replacement.

Product code: G71234

Torx key set with T-handle T9-T50, 10pcs

Torx key set with T-handle. 10pcs, Sizes: T9, 10, 15, 20, 25, 27, 30, 40, 45, 50

Product code: G30591

Tire lever. Lenght: 500mm

This tire changing tool is widened and reinforced, which provides great leverage for tire replacement.

Product code: G71235

Pull bar 3/4" 1.020mm

Pull bar, high resistance and durability, drive head 3/4", length 1.020mm, 180º flexible head, handle material: Acero 40CR

Product code: JBM52524

CV joint boot clamp pliers

CV joint boot clamp pliers. Holes of 1/2" on the handles to use as keys. Opening: 0-20mm.

Product code: JBM52619

Mini fuse assortment, 120pcs

120pcs mini fuse assortment, 20pcs 5A, 20pcs 10A, 20pcs 15A, 20pcs 20A, 20pcs 25A, 20pcs 30A

Product code: JBM53355

Fuel line disconnect plier set, 3pcs

3pcs fuel line coupling disconnect pliers

Product code: JBM53445

Fuel line pliers

Fuel line pliers for removal and replacement of the connections on the in-line fuel filter. Required when replacing the fuel filter or during engine repairs. Suitable for VW, Audi, Mercedes, Fiat, Opel/GM.

Product code: JBM53487

Headlight restoration kit

Designed to restore the clarity to headlight lenses that have become yellowed, cloudy, or hazy.

Product code: JBM53626

6pcs impact adapter set

6pcs impact adapter set, material CrV, sizes 1/4”-3/8”, 3/8”-1/2”, 1/2”-3/4”, 3/8”-1/4”, 1/2”-3/8”, 3/4”-1/2”

Product code: JBM53743

COB headlamp

Portable front light COB, Leds: 3W XPE side + 5W COB front, Lumens: XPE LED 90Lm, COB 350Lm, Battery: 3.7V 1200mAh Li-ion, Material: Silica gel

Product code: JBM54004

Tube double flaring set, 9pcs

Tube double flaring set, 9pcs for brake line tubings.

Product code: K00180

Heat shrinkable solder sleeve set 100pcs

Allows an easy and quick connection of cables, soldering and sealing by placing the cables in the solder sleeve for the subsequent heat application. For wire 0.25-6.0mm2 (26-10AWG)

Product code: JBM53992

1/2” dr. 72t ex-long ratchet wrench

Extra long ratchet with jointed head, drive square 1/2°, 72-teeth, quick release

Product code: JBM53888

Engine timing locking tools set for Citroën/Peugeot 1.0/1.2 VTi

A complete shim and timing lock assembly designed for use on a wide range of vehicles Citroën/Peugeot 1.0/1.2 VTi

Product code: JBM53876

Exhaust pipe clamp pliers

Special tool for removal or installation of exhaust pipe clamps on Citroen, Peugeot, Renault models

Product code: JBM53396

Case with 28 torx sockets

28pcs torx sockets sets, Long: 1/4”: E4, E5, E6, E7, E8; 3/8”: E10, E11, E12, E14, E16; 1/2”: E18, E20, E22, E24; Short: 1/4”: E4, E5, E6, E7, E8; 3/8”: E10, E11, E12, E14, E16; 1/2”: E18, E20, E22, E24; plastic case

Product code: JBM53061

Set of 1/2” extension bars with round end

Set of 1/2” extension bars with round end. Measurements: 50 mm, 125 mm, 250 mm, 380 mm, 510mm.

Product code: JBM51448

Electric ceramic heater 2KW

2kW electric heater. It is equipped with a ceramic heating element which, combined with a strong airflow, ensures quick heating of rooms such as shops, workshops, garages, households, etc.

Product code: G80405

Universal impact swivel joint 1/2"

Universal impact swivel joint 1/2"

Product code: G10520

Tire bead depressor rim clamp

Applies pressure to the tire beads during tire change.

Product code: G71210

Set of screwdrivers and bits, 122pcs

122-piece set of screwdrivers, bits and sockets on a storage rack.

Product code: G32007

Universal socket adapter. For nuts and bolts with 7 to 19mm diameters

Universal socket adapter. For nuts and bolts with 7 to 19mm diameters.

Product code: G15021

Torx T-handle screwdriver set, 9pcs

Torx T-handle screwdriver set, 9pcs. Sizes T10-T50.

Product code: G30587

Screwdrivers set (PH and straight), 9pcs

MAgnetic screwdrivers set (PH and straight), 9pcs

Product code: G30545

Pilot bearing puller. For bearing with inner diameters: 12-38mm

Suitable for removing tight fitted sleeve type bearings and bushings with inner ring diameters of 12 to 38mm.

Product code: G30300

Rechargeable wireless work light. 120LED, Telescopic: 1,2-1,95m, 12V charger

Adjustable and rechargeable wireless work light. 120LED, Telescopic: 1,2-1,95m, 12V charger.

Product code: G15109

Multifunctional socket wrench 48in1. Socket diameters: 8-19mm

It can replace wrenches intended for 12-point, 6-point, 4-point, E-Torx and spline screws and nuts.

Product code: G15030

19pcs torx socket and bit set

19pcs torx socket and bit set. Sockets for external torx: E10, E11, E12, E14, E16, E18, E20, E22, E24. Bits for internal torx: T20, T25, T27, T30, T40, T45, T50, T55, T60, T70.

Product code: G13565

Rolling workshop seat with tool tray

Features a soft, fully padded round seat for added cushioning, making it comfortable to work on your car, truck, SUV, van, and more. Equipped with four 360° rotating wheels which deliver smooth and precise movements.

Product code: G10826

Impact swivel joint adapter set 3pcs, 1/2", 3/8", 1/4"

Set of 3 swivel joint adapters 1/4", 3/8", and 1/2". Swivel joints allow you to access hard-to-reach places and deeply seated bolts. Reinforced chrome-molybdenum steel construction increases the impact resistance.

Product code: G10521

Torque angle gauge 1/2"

Torque angle gauge 1/2"

Product code: G10066

Torque wrench 1/2", 75-300Nm

Torque wrench 1/2", 75-300Nm. The reinforced ratchet has two supports on the rack, which results in increased durability of the wrench mechanism by distributing the force.

Product code: G10061

Telescopic wheel wrench with one 17x19mm and one 21x23mm sockets.

Telescopic wheel wrench with one 17x19mm and one 21x23mm sockets. Total length 34.5cm extends to 50cm.

Product code: G10056

Adjustable wrench 0-24mm, 200mm

Adjustable wrench with a large knurl for easy adjustment and a tight jaw fit. Special hex jaw construction helps reduce slippage and tightly grips the bolt for solid and secure operation.

Product code: G10208

23pcs oil filter wrench set

Set of 21 sockets for unscrewing oil filters. It fits most passenger cars produced on the European, American and Asian markets.

Product code: G10402

Long and short impact socket set 1/2", 10-19mm

Set of impact sockets 1/2" square drive with standard and deep length. Metric socket sizes range from 10 to 19mm.

Product code: G10517

3pcs bit socket set with joints 1/2", 3/8", 1/4"

Bit socket set with joints for 1/4", 3/8" and 1/2" square drive bits.

Product code: G13520

21pcs 12 point socket set. Sizes: 8-36mm

Suitable for both metric and inch (SAE) standard 6 point Torx and 12 point screws.

Product code: G13547

10pcs socket adapter and spline bit set M4, M5, M6, M8, M9, M10, M12, M14, M16, M18

10pcs socket adapter and spline bit set M4, M5, M6, M8, M9, M10, M12, M14, M16, M18

Product code: G13551

14pcs E4-E24 Torx socket set

14pcs E4-E24 Torx socket set. Use with 1/2", 3/8", 1/4" drives.

Product code: G13566

Starter Drive Mini 12V

Starter Drive Mini 12V multifunction 12V lithium starter and power bank.

Product code: 829563

Universal socket adapter. For nuts and bolts with 7 to 19mm diameters

The universal socket is designed to automatically adjust to fit any nut or bolt with 7 to 19mm (1/4" to 3/4") diameters.

Product code: G15020

E-Mobility Mastercharge 370 230V

E-Mobility Mastercharge 370 230V Charging station for electric vehicles in AC alternating current (Mode 3).

Product code: 893001

Hydraulic hose crimping tool set

Set contains the hand-operated hydraulic crimping tool, four sets of dies for standard fittings and four sets of dies for reduced barrier fittings.

Product code: G00905

Self-priming 12V DC diesel fuel transfer pump

Self-priming 12V DC diesel fuel transfer pump with direct drive and inner recirculation to extend pump life. Ideal for transferring diesel, light oils and kerosene.

Product code: G01022

Long Torx key set T15-T55 9pcs

Long Torx key set T15 - T55. Set includes 9 pieces of long Torx key wrenches: T10, T15, T20, T25, T27, T30, T40, T45, T50, T55.

Product code: G01707

Ratchet combination spanner set with flexible head 6-32mm, 22pcs

Ratchet combination spanner set with flexible head 6-32mm, 22pcs. 12-point ratcheting end needs as little as 5 degrees to rotate bolts.

Product code: G10342