Mounting pad set for bearings, 52pcs

Non-marring hook, pick and prying tool set, 6pcs

This set allows you to remove, clean, and work on trim clips, oil seals, grommets, O-rings, air vent assemblies, tight gaps in interior automotive compartments, delicate wiring, composite electrical connectors, and other sensitive finished components.

Product code: JBM54142

Rear bearing hub puller, Citroen; Peugeot ; Toyota ; Opel after 2016

This tool is designed for the removal and installation of wheel bearings, especially on specific vehicles models after 2016. The design eliminates the need to remove the steering knuckle and ABS sensor and simplifies the repair process.

Product code: W0736

Pulley puller three-armed 40-85mm

The Three-Armed Pulley Puller is a versatile tool designed for removing pulleys from various mechanical systems. It is particularly useful for pulleys with a diameter ranging from 40mm to 85mm.

Product code: W0601

Internal bearing puller set, 12-32mm

This internal bearing puller set with slide hammer is perfect for pulling pilot bearings and other internal clamping jobs. Gripping sizes range from 11-32mm.

Product code: MG50140

Internal bearing puller tool set, 8-58mm

This internal bearing puller tool set can handle jobs requiring clamping, with a capacity of 8-58mm. Includes 3 threaded adapters and 11 gripping sizes. Easy and efficient!

Product code: MG50148

Bearing puller set, 14pcs

Designed for pulling bearing off shaft and separating bearing housings.

Product code: DK-230589

Bearing and seal drive-in set, 10 pcs

Bearing and seal drive-in set, 10 pcs. specially used for installing bearing rings and seals.

Product code: MG04J1040

Adjustable timing pulley puller

An adjustable timing pulley puller is a special tool used in the assembly process of engines.

Product code: MG04A2213

Hydraulic cylinder to the pullers, press and injectors - 15 Ton

With a 15-ton pressing force, this hydraulic cylinder delivers exceptional power to handle tasks. Whether you need to remove stubborn parts, press components together or work with injectors, this cylinder provides the necessary force to get the job done efficiently.

Product code: W0432

Rocker pin puller and press for T4, Master, Movano, Interstar, Sprinter, VW LT

Press for upper bolts T4, Master, Movano, Interstar and lower bolts Sprinter, VW LT

Product code: W0093

Puller for front control arm pins of Renault Master, Opel Movano

Puller for front control arm pins of Renault Master, Opel Movano

Product code: W0045

Hydraulic bearing puller kit, 10T

Suitable for pulling hubs, flanges, gears and bearings.

Product code: DK-230584

Injector gasket puller

For the extraction of copper sealing gaskets and washers within injector seats.

Product code: MG04A3079

Internal bearing puller set

Internal bearing puller 10-32 mm. A professional set, necessary in every workshop.

Product code: CKB04004

Bearing puller set, 9pcs

It’s ideal for removing small gears, wheels, and fittings from shafts also can be used to replace the steering pump, perfect for wiper arm assembly, rebuilding your alternator, removing tightly fitted pulleys, and reaches places that regular gear pullers can’t access.

Product code: DK-230590

O-ring and oil seal removal tool

Universal double hook puller for removing O-rings and oil seals.

Product code: CKB04117

Seal and plug removal hook set

Seal and plug removal hook set. 3 pcs. (15.5, 16.5, 12cm)

Product code: JBM53053

Two jaw gear and bearing puller. Operating range: up to 100mm

Two jaw gear and bearing puller with adjustable clamping depth and width.

Product code: G02200

Inner bearing puller set. For diameters: 10-32mm

The internal bearing puller designed for dismounting internal bearings with an internal diameter of 10-32mm.

Product code: G02747

Two jaw gear and bearing puller. Operating range: up to 150mm

Two jaw gear puller with adjustable clamping depth and width.

Product code: G02201

Two jaw gear and bearing puller. Operating range: up to 200mm

Two jaw gear and bearing puller with adjustable clamping depth and width. For both internal and external bearings.

Product code: G02202

Bar type gear and bearing pullers with two jaws. Working range: 250mm

Two jaw gear puller with adjustable clamping depth and width. For both internal and external bearings.

Product code: G02203

Bearing and gear puller with 3 jaws. Working range: up to 3" (75mm)

Bearing and gear puller with 3 jaws. Working range: up to 3" (75mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02230

Bearing and gear puller with 3 jaws. Working range: up to 4" (102mm)

Bearing and gear puller with 3 jaws. Working range: up to 4" (102mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02231

Bearing and gear puller with 3 jaws. Working range: up to 6" (152mm)

Bearing and gear puller with 3 jaws. Working range: up to 6" (152mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02232

Bearing and gear puller with 3 jaws. Working range: up to 8" (203mm)

Bearing and gear puller with 3 jaws. Working range: up to 8" (203mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02233

Bearing and gear puller with 3 jaws. Working range: up to 10" (254mm)

Bearing and gear puller with 3 jaws. Working range: up to 10" (254mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02234

Bearing and gear puller with 3 jaws. Working range: up to 12" (305mm)

Bearing and gear puller with 3 jaws. Working range: up to 12" (305mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02235

Bearing and gear puller with 3 jaws. Working range: up to 4" (102mm)

Bearing and gear puller with 3 jaws. Working range: up to 4" (102mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02242

Bearing and gear puller with 3 jaws. Working range: up to 6" (152mm)

Bearing and gear puller with 3 jaws. Working range: up to 6" (152mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02243

Bearing and gear puller with 3 jaws. Working range: up to 8" (203mm)

Bearing and gear puller with 3 jaws. Working range: up to 8" (203mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02244

Bearing and gear puller with 3 jaws. Working range: up to 10" (254mm)

Bearing and gear puller with 3 jaws. Working range: up to 10" (254mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02245

Bearing and gear puller with 3 jaws. Working range: 12" (305mm)

Bearing and gear puller with 3 jaws. Working range: 12" (305mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02246

Gear and bearing puller with 3 jaws. Max capacity: 14" (350mm)

Gear puller with 3 jaws 14" (350mm). The puller enables the removal of bearings (internal and external) from various types of shafts and houses.

Product code: G02247

Internal bearing extractor set. Diameters: 8-58mm

Precision puller for tight-fitting, internal bearings and bushings.

Product code: G02577

Wiper arm puller

Wiper arm puller. The puller is used to remove car wiper arms. Made of durable chrome-molybdenum steel.

Product code: G02770

Pilot bearing puller. For bearing with inner diameters: 12-38mm

Suitable for removing tight fitted sleeve type bearings and bushings with inner ring diameters of 12 to 38mm.

Product code: G30300

Pilot bearing puller. For bearing with inner diameters: 12-38mm

Suitable for removing tight fitted sleeve type bearings and bushings with inner ring diameters of 12 to 38mm.

Product code: G30301

Hydraulic wheel hub puller 10T

Hydraulic wheel hub puller 10T

Product code: MG04B1044B

Hook and pick set, 9pcs

Hook and pick set for removing oil seals, o-rings and gaskets

Product code: G02708

Set of hooks 4 pieces

Set of 4 hooks. Hooks have hardened chrome tips. The handle is made of high-quality non-slip material. Total length of tools - 135mm.

Product code: CKB04710

Hook and pick set 6pcs (Lenght: 240mm)

Hook and pick set for removing seals, O-rings and gaskets.

Product code: G02706

Windshield wiper arm/battery terminal puller, capacity 25-43mm

This dual-purpose puller easily removes stuck and jammed battery terminals and wiper arms. It is also suitable for removing battery lugs and generator bearings.

Product code: MG50151

Wheel bearing removal/installing tool set

For the VAG group, wheel hub size 72mm, Audi A2, Skoda Fabia after 2000, VW Polo, Fox after 2005, Seat Ibiza after 2002.

Product code: MG50432

Wheel Bearing tool VW

Bearing installation and removal tool for 85mm bearings. Application Volkswagen Touareg, Transporter, Multivan & T5

Product code: MG50432A

Wheel bearing removal/installation tool set 50-88mm

Diminishes the possibility of wheel bearing damage during removal and installation. Sizes (d) 50, 55, 60, 64, 67, 70, 72, 74, 75, 78, 82, 84, 88mm.

Product code: MG50075

Front wheel drive kit, 55.5-91mm, axle 380mm

Sizes(d) 55.5, 59, 62, 65, 66, 71.5, 73, 78, 84, 86, 91mm, axle 380mm

Product code: MG50405

Universal puller set

Universal puller set, jaw length 100, 200, 250mm

Product code: MG50131

Bearing separator set

Bearing separator set, capacity 30-50mm, 50-75mm, 2 separators, 1 forcing screw, 4X2 extensions

Product code: MG50132

Stud extractor, 1/4"-3/4"

A stud driver (also known as a stud puller) is a tool that is commonly used in automotive repair when a stud is stuck or cracked in the vehicle's chassis or other structural component.

Product code: MG50047

Stud Wrench 8" 12-21mm

Fully adjustable with a one-handed squeeze. Efficient ratcheting by releasing, then re-gripping the object. Often removes nuts and bolts damaged by other tools.

Product code: G00860

Bearing puller 10-30mm

The clamp can be adjusted with screws 10-30mm. It is suitable to extend existing inventory. With the scraper you can accurately remove the bearing without damaging it.

Product code: MG04J1171

Windshield wiper puller

Windshield wiper puller, max. diameter 45mm, min. diameter 17mm, simple handling, safe mechanism, design with thin legs and brass-finished ends. Weight 0.2kg.

Product code: JBM52454

Bearing separator set

Bearing separator set, capacity 30-50mm, 50-75mm, 2 separators, 1 forcing screw, 4X2 extensions

Product code: JBM51125

Wheel bearing removal/installation tool set 55.7-88.4mm

Diminishes the possibility of wheel bearing damage during removal and installation. Sizes (d) 55.7, 63.3, 67.8, 70.7, 71.9, 71.7, 72.8, 73.4, 74.7, 77.4, 81.4, 83.3, 88.4mm.

Product code: JBM52551

Hydraulic jaw puller set 10t

Multi-function puller with adjustable two or three leg function. Allows bearings, gears, etc. to be easily removed with minimal effort by use of the hydraulic puller.

Product code: G00911

Hydraulic hose crimping tool set

Set contains the hand-operated hydraulic crimping tool, four sets of dies for standard fittings and four sets of dies for reduced barrier fittings.

Product code: G00905

Hydraulic jaw puller kit 5t

Multi-function puller with adjustable two or three leg function. Allows bearings, gears, etc. to be easily removed with minimal effort by use of the hydraulic puller.

Product code: G00910

Hydraulic jaw puller set 20t

Multi-function puller with adjustable two or three leg function. Allows bearings, gears, etc. to be easily removed with minimal effort by use of the hydraulic puller.

Product code: G00912

Bush, bearing and seal driver set 52pcs

Bush, bearing and seal driver set 52pcs. Discs: 18 - 65mm and 74mm

Product code: CKBB1035

Adjustable timing pulley remover 42 - 82mm

Adjustable timing pulley remover 42 - 82mm

Product code: CKBA2213

Bearing race and seal driver set. 17 pcs

This set makes it easy to insert bearing races and seals without damage to the bearing race, seals and housing. Fits most standard seals and bearing sizes.

Product code: CKB04013

Bushing and seal driver set 40-81mm 10 pcs

The set is used for bearings, sealants, bushings, etc. 40, 44, 50, 59, 63, 65, 72, 76, 81mm

Product code: CKB04270

Hollow hydraulic cylinder 12t

Hydraulic cylinder with through and threaded hole. It can be used with various types of mechanical presses that are designed for the extraction of metal and rubber silents, pins, joints, etc.

Product code: C07/0098

Hollow hydraulic cylinder 20t

Hydraulic cylinder with through and threaded hole. It can be used with various types of mechanical presses that are designed for the extraction of metal and rubber silents, pins, joints, etc.

Product code: C07/0112

Puller to the wiper arms - universal 50x40

Puller to the wiper arms - universal 50x40 designed to provide efficient and reliable removal of wiper arms from a wide range of vehicles, including newer car models. This puller has been developed based on the design by Machanikow and has undergone extensive testing on various new cars, ensuring its effectiveness and performance.

Product code: W0119

Puller to the hub / bearings VW T5

Puller to the hub / bearings VW T5

Product code: W0129

Hub Puller VW, Seat, Skoda-Puller with ABS and without ABS

The tool is suitable for removing the wheel hubs of both vehicles with and without ABS. Therefore, it can be widely used when servicing VW, Seat and Skoda models. The tool fits exactly on the hub and provides the right grip to pull the hub off efficiently and safely.

Product code: W0163

Double-row bearing puller and wheel hubs II version (BMW, Mercedes etc.)

Double-row bearing puller and wheel hubs II version (BMW, Mercedes etc.)

Product code: W0205

Universal sliding hammer hub puller, with 15 screws

Universal sliding hammer hub puller, with 15 screws

Product code: W0002

Universal wiper arm puller

Universal wiper arm puller. Two paws type.

Product code: W0123

Puller hub bearing the brake disc Ford Transit

The puller hub bearing the brake disc is a special tool used for mounting and dismounting brake disc bearings on Ford Transit vehicles.

Product code: W0500

Puller for wheel hub / bearing rear swingarm Mercedes Vito Viano 2.2 CDI after 2003

This puller is designed to safely and efficiently separate the wheel hub or bearing from the swingarm assembly.

Product code: W0361

Power steering pump puller

This tool facilitates the safe removal of the power steering pump.

Product code: W0430

Timing belt and injection pump pulley puller

This puller is a go-to tool for removing timing belt and injection pump pulleys from a wide range of engines, including those found in the VW Audi group and other compatible vehicles.

Product code: W0033

Internal bearing puller ⌀35mm

Internal bearing puller is a special tool designed to remove gear bearings with an inner diameter of 35 mm.

Product code: W0291

Tool for hub removal (set of 15 screws)

Tool for hub removal – cars of A, B, C class and others. Set of 15 screws.

Product code: W0072

Puller hub bearings Renault Trafic, Opel Vivaro 2.0 DCI

Product code: W0487

Puller for wheel hub / bearing Ford Focus II, C-Max, Volvo, Mazda 3,-puller with ABS and without ABS

Product code: W0305

Puller for wheel hub / bearing with and without Abs - Ford Mondeo, Focus, C-Max, Mazda 3, Volvo C30 C70 S40 V50

Product code: W0359

Puller for wheel hub / bearing VW Polo, Seat, Skoda, Audi A2-puller with ABS and without ABS

This puller is specifically designed to handle wheel hubs and bearings on VW Polo, Seat, Skoda, and Audi A2 vehicles. Whether your vehicle is equipped with ABS or without ABS, this versatile tool ensures a secure grip and effortless removal.

Product code: W0306

Puller hub / bearing Fiat Ducato Citroen Jumper

Product code: W0499

Extra feet puller for beam puller (W0033)

Extra feet puller for beam puller (W0033)

Product code: W0150

Crankshaft pulley puller VW / Audi 4 and 5 cylinder

Engineered specifically for the removal of crankshaft pulleys in certain VW and Audi vehicles. Ensures smooth and damage-free extraction of crankshaft pulleys, a vital component in the engine's belt system.

Product code: W0173

Puller for belt pulleys, three-arm with extended arms

Puller for belt pulleys, three-arm with extended arms

Product code: W0070

Puller for belt pulleys, four-arm, 60mm

The four-arm 60mm pulley puller is a special tool used to remove pulleys. This tool is specifically designed for attaching and removing four-arm pulleys.

Product code: W0089

Puller hub / bearing Mondeo IV; Focus II RS (FORD 1 463 833)

This tool is designed for the assembly and disassembly of the front hub and bearing on Ford Mondeo IV and Focus II RS vehicles.

Product code: W0506

Press, puller for bolts of suspension arm, front Master/Movano/Interstar

This tool has a combined press and puller function, which allows convenient and efficient handling of the suspension arm pins. With the press function, the tool is able to press or unpress the pins from the rocker arms, ensuring accurate and stable pin insertion or removal.

Product code: W0097

Adapters for press, puller for bolts, Master, Movano, Interstar

Adapters for press, puller for bolts, Renault Master, Opel Movano, Nissan Interstar

Product code: W0102

Press and puller for ball joints Renault, Opel, Iveco, VW, Nissan, Mercedes etc., 20 adapters

Universal press and puller for ball joints Renault, Opel, Iveco, VW, Nissan, Mercedes etc., with 20 adapters. For models manufactured in 2006 and on.

Product code: W0162

Universal AC clutch remover

Universal disc with a centering mandrel for the removal of car air conditioning clutches.

Product code: W0013

Press, puller for bolts (W0027, W0102, W0116), Mercedes, VW, Opel etc.

Press, puller for bolts (W0027, W0102, W0116), Mercedes, VW, Opel etc.

Product code: W0133

Slide hammer, weight 1.5kg, M12/M16

The use of this slide hammer allows you to create powerful impacts to loosen or remove jammed or stuck parts.

Product code: W0066

Hardened M12 nut with bearing for pullers

Hardened M12 nut with bearing for pullers

Product code: W0149

Adapters for press, puller for bolts VW T4, LT, Mercedes Sprinter

The adapters allow the removal and installation of bolts in VW T4, LT and Mercedes Sprinter vehicles.

Product code: W0147

Slide hammer, diameter 70mm, weight 0.9kg, length 300mm

Slide hammer, diameter 70mm, weight 0.9kg, length 300mm

Product code: W0060

Slide hammer M12/16, ⌀85mm, weight 1,3 kg

A slide hammer can be a useful tool when installing or removing fasteners that are difficult to move or fit tightly. The large diameter and weight of the M12/16 slide hammer allows for greater impact force, which can more effectively drive in or squeeze out these elements.

Product code: W0048

Press, puller for bolts of suspension arms Opel, Renault, Nissan

Press, puller for upper and lower ball bolts of the suspension arms in Master, Movano, Interstar.

Product code: W0100

Upper control arm central bolt puller for VW, Audi after 2005

Upper control arm central bolt puller for VW, Audi after 2005.

Product code: W0164

Puller for belt pulleys, three-arm

A puller for removing gears. Central screw diameter: 16mm. Adjustable clamping diameter: 42-82mm. Arm length: 35mm. Full length: 55mm.

Product code: W0068

Adapters for press, puller for bolts, Master, Movano, Interstar

Adapters for press, puller for bolts, Renault Master, Opel Movano, Nissan Interstar

Product code: W0098

Puller for belt pulleys, four-arm

Puller for belt pulleys, four-arm is a high-quality and efficient tool that makes belt replacement and maintenance easier. This extremely useful tool allows precise adjustment of the tension of the belts.

Product code: W0073

Slide hammer for injector pulling, weight 2.5kg, M12/M16

Slide hammer for injector pulling, weight 2.5kg, M12/M16.

Product code: W0067

Slide hammer, weight 1kg, M12/M16

The use of this slide hammer allows you to create powerful impacts to loosen or remove jammed or stuck parts.

Product code: W0065

Adapter to remove the pins down on the Renault Master 2006

Adapter to remove the pins down on the Renault Master 2006

Product code: W0160

Press for silents and ball joints, for VW T4, Mercedes Sprinter, VW LT

Press for mounting and removing silents in the suspension arm in VW T4, VW LT and Mercedes Sprinter 1999-2006 without having to remove the arm from the vehicle.

Product code: W0027

Press for dismantling and mounting of lower bolts, IVECO

Press for dismantling and mounting of lower bolts, IVECO

Product code: W0115

Puller for double-row wheel hub bearings

Puller for double-row wheel hub bearings. Mechanical kit to facilitate work with double-row front and rear axle bearings. The purpose of the puller is to safely remove this type of bearing from the wheel hub.

Product code: W0037

Press, puller for bolts, strengthened (W0027, W0102)

Press, puller for bolts, strengthened (W0027, W0102) Mercedes Sprinter, Renault Master, Opel Movano, Nissan Interstar, VW T4. The set includes a press and a puller, which have a combined function. The reinforced design and durable materials ensure a reliable and long service life. The set contains the necessary accessories and adapters for different types of vehicles, so that it can be widely used during work.

Product code: W0134

Universal puller (screw L=100mm, hole distance 27-62mm)

Universal puller (screw L=100mm, hole distance 27-62mm)

Product code: W0136

Adapter for removing bolts VW Crafter, Mercedes Sprinter 906

Adapter for removing bolts in VW, Mercedes upper and lower control arms. The adapter is to be used with W0027, W0133, W0134 etc.

Product code: W0141

Press, puller for bolts Renault Master / Opel Movano

Press, puller for bolts Renault Master / Opel Movano + W0160 adapter

Product code: W0161

Set of adapters for dismantling and mounting of lower bolts, IVECO

The adapter kit is precisely engineered and durable, and allows reliable and efficient removal and installation of lower suspension bolts. Designed to IVECO vehicle specifications to fit perfectly with the lower suspension bolts and allow smooth and safe operations.

Product code: W0116

Adapters for press, puller for bolts, Renault Master, Opel Movano

Adapters for press, puller for bolts, Renault Master, Opel Movano. It cooperate with W0027 and W0045 presses.

Product code: W0046