Special promotions are available! Don't miss out on great deals!
Steering and suspension tools
Categories
Products
Steering Rack Side Nut Wrench for Dodge, Mercedes-Benz, VW
This specialized nut socket is designed for efficient mounting, dismounting, and adjustment of steering rack side tightening nuts. Manufactured by MSG Equipment, it ensures safe and damage-free handling during steering system maintenance and repair.
Product code: MS00010
Wrench for bottom nut of worm gear steering rack for numerous models
This specialized nut socket is designed for the precise installation and removal of the bottom nut of the steering rack worm gear. It ensures safe, damage-free handling and high-quality repairs for steering rack pinions. It is suitable for the following models: Chrysler, Citroën, Ford, Hyundai, Kia, Mazda, Mitsubishi, Peugeot, Seat, Volkswagen (VW).
Product code: MS00009
Wheel hub puller with sliding hammer, 6pcs
6-piece forged wheel hub puller with 1600g sliding hammer and thread adaptors; total length approx. 510mm.
Product code: BGS-7745
Wheel Bearing Tool Set, 31pcs
31-piece universal tool set for on-vehicle wheel bearing and hub disassembly/assembly.
Product code: BGS-67301
Wheel Bearing Tool Set for Peugeot, Renault, Citroën
Complete tool set for removing and installing wheel bearings on Peugeot, Renault, and Citroën vehicles.
Product code: BGS-8739
Wheel Bearing Mounting Disc Set, 52 pcs
52-piece set for mounting bearing shells, seals, and bushings. Ø18–65 mm + 74 mm discs. Usable with press or hammer.
Product code: BGS-98467
Power steering pump hub puller
A universal power steering pump hub puller for quick and safe removal of pulley hubs without deformation. Compatible with all car models.
Product code: MS00042
Pressing screw for hub and pulley of power steering pump (M12/1,5) for MS00126 tool
Universal pressing screw (M12/1.5) for press-fitting hubs and pulleys on power steering pump shafts. Compatible with all vehicle makes and models.
Product code: MS00046
Universal power steering pump hub puller
Specialized universal tool for safely removing power steering pump pulleys while preserving the integrity of both the pulley and the pump.
Product code: MS00080
Ball Joint Separator, extra large, for utitlity vehicles
Forged ball joint separator for trucks and utility vehicles, universal use, 270mm long, 1186g.
Product code: BGS-1802
Tester for diagnostics of power steering system
The MS511 tester is designed for diagnosing power steering system components such as steering racks and pumps without removal from the vehicle. It evaluates fluid pressure and flow rate, helping determine if repairs are needed.
Product code: MS511
Test bench for diagnostics and flushing of power steering system
MS503N is a universal test bench for power steering systems operated from 230V mains. The test bench for system flushing and evaluation of the technical condition of a power steering rack or pump.
Product code: MS503N
Tester for diagnostics of power steering system
The MS510 tester is used for diagnosing the hydraulic power steering system by determining the pressure generated by the vehicle's power steering pump in different operating modes (with load and without).
Product code: MS510
Mechanism for testing hps racks under load
The MS521 mechanism simulates load resistance on HPS/EPS racks, allowing precise fault detection, including leaking valves, worn seals, and cylinder wear. Works with MS502M test bench and MS561 controller.
Product code: MS521
Test bench for diagnostics of power steering pumps
Test Bench MS504 is used for evaluation of the technical condition and output characteristics of mechanically driven single- and double-circuit pumps. The bench simulates operation of the tested unit in a car.
Product code: MS504
Test bench for diagnostics of power steering racks
The MS502M test bench is designed for hydraulic power steering (HPS) rack diagnostics, allowing real-time performance simulation and detection of faults like leaks, packing seal wear, unit body damage, and Teflon ring deterioration.
Product code: MS502M
Test Bench for shock absorbers
A professional test bench for evaluating the performance of all types of passenger car shock absorbers, supporting diagnostics, post-maintenance checks, and research applications.
Product code: MS201
Swivel Vise for shock absorbers and steering racks
Swivel vise for safe and efficient assembling and disassembling of shock absorbers and steering racks.
Product code: MS20002
Devices for refueling shock absorbers
A specialized system for refilling mono-tube and twin-tube shock absorbers with gas after repair, with pressure adjustment up to 120 bar.
Product code: MS200
Ball Joint Puller for Mercedes W221 4Matic
Ball joint puller for safe and easy dismounting of suspension ball joints on Mercedes W221 4Matic vehicles.